1068650682 Kenmore Refrigerator - Instructions

Took just a few moments to install. The parts fit like a glove,

I removed the broken end cap and then I snapped the metal shelf onto both end caps and replaced the shelf.

I really must say that dealing with PartSelect was exceptional. It took about three days for me to get the part and, prior to that, it was very easy for this sidewalk fixer to locate the correct part on their website. Thank you for your excellent service.

Unplug Dryer. Remove 2 5/16in hex screws from lower panel and remove panel.Remove 3 5/16in hex screws attaching lint duct. Remove 8 1/4in hex screws attaching blower housing. Remove 2 1/4 hex screws attaching thermostat to blower housing. Using adj. wrench on back of motor shaft nut to hold, loosen fan assy. w/ 7/8in socket. Remove 3 5/16in hex screws holding fan housing to motor mount. Remove 2 5/16in hex screws holding housing and motor mount to base floor. Push belt pulley wheel up enough to loosen belt and take off rear motor pulley. Motor w/mount can be slid out bottom for replacement [wires are layed toward front].Using 6in flat tip screw driver press down to unlock front & back motor bushing holddown clamps. Pinch electrical wire connector ends to pull off old motor. Remove and Install new motor, reversing steps. Belt replacement [suggested w/new motor] requires removal of 2 5/16in screws to lift/remove door w/front panel [disconnect door switch wires upper right rear corner].Remove 4 5/16 screws holding front bulkhead. Once bulkhead is pulled up and off, allow front end of drum to sag and rest IN PLACE [removal not required to slip old belt off and install new belt]. Note belt location point around drum. Slide new belt on. Reinstall bulkhead and panel/door [Don't forget door swich wires]. Adjust belt into position and push spring-held belt pully up to allow looping of new belt around rear motor belt pulley. Complete w/hand turning of drum to ensure belt is aligned and feeding properly. Reinstall lower fan housing/covers/thermostat,etc removed for motor installation.

The repair was easy. The amazing story was that I ordered the part around 12:00 noon on Friday December 21st and it arrived by USPS mail the next day Saturday December 22, right in the heat of the Christmas rush.

This website saved my marriage. For the past two years, every time we would open the fridge everything in the door shelves would fall all over the floor. This was not only embarassing when we would have family and friends over but I really got tired of my wife yelling every time she would open up the fridge. I tried every type of glue and repairs to try and fix it, finally gave up and thought the only way I would find peace at home was to purchase a new fridge. I accidently stumbled across your website and before I knew it and about $6 later my life improved more than you can imagine. The best part was how easy it was to find the part I needed with the detailed pictures you have. The part was shipped fast and very easy to install. I will definately use partselect again. Thanks!

alined the new part and snapped it on.

Pulled out the refrigerator and removed the two panels from the rear of the refrigerator. Removed the fan held in by four screws and unplugged the connector. Soldered on the original connector, installed the fan to the motor and re-installed the unit into the refrigerator. Then blew out and vaccumed the condenser coils.

Removed rear cover to see non-operating fan - removed three mounting screws on the motor that were a challenge to access. Swapped fan from old motor onto new motor - one threaded nut on the motor shaft. Spliced new fan wires into fan wires of the wiring harness and mounted with three self-tapping screws supplied with new fan motor. Replaced rear cover and plugged it in! Now the refrigerator cools like new (1981 model side-by-side Admiral)

Replaced both since they came as a set. The only way it could have been any easier is if I had the wife do it. She had the remote this time. (•¿•)

One of the front studs was broken off. I had to use pliers to pull it out (kind of tight). Then I inserted the back and front holders and layed the shelf back in. Total time...10 min

Just like the video showed me.It still does not work. Have to turn it off and on to make it start up.I also replaced thermostat in freezer. Does not work.

Replaced broken shelf bracket

Well the part and repair was so easy my wife did it and is very proud of herself

removed retaining bar removed and replaced end cap and reinstalled retaining bar.

Just replaced the old piece with the new. Simple and easy.