25331672100 Kenmore Refrigerator - Instructions

I ordered the part and snapped it on the door.

Unplug, remove 2 screws off back panel inside the freezer. Cut wires on old one and crimped in new one. Light to melt the shrink wrap that came with it. Pretty easy.

I removed the two side mount screws with a screwdriver and disconnected the electrical plug to the ice maker to remove it. I reversed the process to install the new one.

It was the thermostat that was the problem, but I chose to replace the entire ice maker for only $25 more.

Turned off fridge circuit breaker
Removed all food from freezer and put in cooler.
Removed shelves from freezer
Removed ice maker
Removed 2 hex head screws
Tilted back evaporator cover and tried to unplug connection.
Found connection was iced over with a huge block of ice coming from water inlet to ice maker
Spent several hours trying to melt and chip away ice without damaging fridge.
Finally was able to break up ice with long flat head screwdriver and hammer.
Unplugged connector and was able to remove evaporator cover.
Cut wires near thermostat and removed
Stripped wire as needed and crimped new thermostat in place.
Used heat gun and lighter to melt heat shrink. This took a long time and required a lot more heat than expected.
Reconnected evaporator cover connection and reattached cover.
Reinstalled ice maker
Reinstalled shelves.
Put food back in
Turned circuit breaker back on.

1. I took out one screw on the ice maker and loosened the other two screws and unplugged and removed the ice maker.
2. Next I took out 2 screws from the bottom of the auger drive box and unplugged the wiring harness and removed the box. The wiring harness was a little tricky. The lock on the plug pushes in to unlock even though it looks like it pulls out,.
3.next you must remove 2 screws from the left side bracket that holds the auger box and remove the bracket.
4.Now take out 8 screws that hold the back panel in place and remove the back panel.
5. now your looking at the evaporator fan blade and motor. The simple way to replace the fan blade is to unplug the motor and remove it from the freezer. It just sits in with nothing holding it. The fan requires a little pressure but should pull right off. Install new fan blade and put everything back in the same order it was removed.

The bulb has a plastic clear cover. That cover can just be carefully removed using a screwdriver. It's held in by a metal bracket. After you remove the cover. You'll just need to replace the bulb and then re-install the cover and bracket.

Remove the cardboard access cover at the bottom back of the fridge. On the left side, locate the run capacitor. Remove it by prying it loose from its socket, after first removing the wire hold down clamp. One wonders why the clamp is there, which makes it difficult to get the run capacitor out. Be careful not to disrupt in any way the copper refrigerant tubes. If you mess them up, you will have wasted your time and effort trying to repair the machine. I was lucky, since a failed run capacitor is the problem only about 12% of the time, based on what I’ve read. Hallelujah! It was the problem with my fridge.

BOUGHT NEW ICEMAKER TOOK TWO SCREWS OUT, UNPLUGGED THE ELECTRICAL CONNECTION. REMOVED OLD ICEMAKER, PUT TWO SCREWS BACK INTO REFRIGERATOR(DON'T SCREW ALL THE WAY IN AS THE NEW ICE MAKER WILL FIT ON. HOOK ELECTRICAL CONNECTION AND ADAPTER (THAT COMES WITH IT). PUT THE DRAIN TUBE IN ITS SPOT, HOOK ICE MAKER ONTO THE TWO SCREWS TIGHTEN EM DOWN. I DID THIS RIGHT BEFORE I WENT TO A BIRTHDAY DINNER WITH MY HUSBAND, WAS ALREADY DRESSED AND READY TO GO AND I TOLD HIM ILL PUT IT IN SO WE CAN HAVE ICE WHEN WE RETURN. ENDED UP BEING A SURPRISE PARTY FOR ME AND WHEN WE RETURNED WE HAD ICE. IT WAS SO EASY EVEN A GIRL CAN DO IT!!

I watched the instructional video and did what it said.

After disassembling, the thermal fuse I ordered were not and exact fit, I had to cut off the ring terminals, strip the insulation back and splice it in.
It works.

I watched the video on how to change the defrost thermostat. I removed the back cover inside the freezer then I pulled off the old defrost thermostat and then using a pair of wire cutters I cut it off and then bared a little of both of the wires and then slid the heat sherink and wire connectors on the existing wires and then slid the other ends of the wires into the wire connectors then crimped the ends of the connectors and then tried using heat on the heat shrinks but still used rubber electric tape over it. I clipped the new thermostat were the old one was and then reattached the freezer wall cover and plugged the refrigerator back in. 24 hours later I checked the temperature in the refrigerator and freezer and both are running a lot colder.

Turned off water to inlet valve. Unbolted valve from back of unit, disconnect water supply line from valve, disconnected water line to ice maker. Put on new compression ring around water supply line. Pressed ice maker line into new valve, installed valve back on unit, then connected main supply line to valve. Works like a charm.

inside the freezer compartment, remove four hex head screws from rear panel,lift panel forward and unplug wire assembly from panel. find old defrost thermostat attached to copper tube by clip on back of thermostat, unclip, snip two wires to thermostat, take new thermostat, strip 1/4"of wire from wires in freezer (thermostat is prestripped),insert light blue wire from thermostat and light blue wire from freezer into opposite ends of crimp connector and crimp securely. repeat with dark blue wires. set panel back in freezer,connect plug to back of panel, refasten screws and you are go to go! save yourself the price of a new refrigerator or $300 repair by repairman!

Unscrewed (loosen) screws lifted unit out unplugged electrical connection. plugged in unit hung on screws tightened screws and had ice in less then 1 hour. Rick

Unscrewed the broken part, lined up the new door handle and screwed it on. Easy Peasy! I'm a 78 year old grandmother.