10654909300 Kenmore Refrigerator - Instructions

Determined that compressor was not running, after researching problem on another site they recommended i try the condenser moor fan or motor, the defrost thermostat or defrost timer. . I was not satisfied with their recommendations. If I had tried their recommendations i would have likely gotten frustrated and spent upwards of $3000 to replace the 22 year-old hand me down unit. Thank you Parts Select for properly diagnosing my relay failure saving me a ton of money.

Removed ice maker from fridge. Removed motor assembly (3) screws on cover, and (2) screws inside. Removed mold (3 screws on bottom) and replaced everything in reverse order. Note: Turned ice maker off for several days while waiting for parts. The water line on this particular model will freeze inside the freezer if ice isn't made for several hours/days. You will have to defrost to begin making ice again.

Followed on line video

Long shaft from motor to dispenser was stripped. I removed 2 screws from the shaft holder in door, lifted old shaft out, put new shaft in and replaced the 2 screws. Took 2 mins! Works great!

This one is not rocket science, however, it does take some careful "fudging" to accomplish without additional disassembly. The Ice Guide is held in place by three tabs. The tricky part is "tilting" the center tab into it's hole/slot on the ice dispenser lever (center hole), then tilting it up to snap into place.... there is a very tight tolerance here, with the opening of the ice/water dispensing unit. Be sure to "lock out" the ice maker/water dispenser, in order to be able to use the light. Once snapped in place, all is well.

I removed two small bolts that secure the flapper that keeps ice from falling out when you open the door, one bolt that holds a cosmetic cover for the wires and slid the icemanker forward. The only difficult part was removing the plug since it was high up, the wires were stiff and there's a release to push that locks the two plugs together. Once it was removed all was installed in the opposire order.
The part I ordered had a slightly taller channel where the water refills so I had to trim it to allow the new icemaker to slide in without bending the fill nozzle. Other than that it was pretty easy.

Very easy to order from parts select. Took seconds to replace.

ordered the part, pulled out the icemaker unit, removed the module, put the new module in, reinstalled the ice maker unit and let it run.

I followed the instructions that was on your site and it was very easy to follow.

directions very well written, easy to follow, no problems

With instructions from PartSelect.com this was an easy fix. I tested the motor's electric as suggested and was satisfied that the Motor Module (WPL W10190935) would correct the problem. UNPLUG THE REFRIGERATOR! I popped the outside plastic cover off to expose the unit. (1) remove the wire unit that runs the length of the cube maker (2) remove the 3 screws that secure the motor unit and carefully remove it (3) carefully line up the new unit, slide in place and replace the 3 screws (4) install the wire that was removed in step(1). Connect electric to the refrigerator and wait about 2 hours for your first ice cubes. PartSelect.com is the ONLY supplier that you will ever need! Great instructions and trouble shooting suggestions. Shipping is incredibly fasssst! Customer contact is awesome. Don't hesitate to buy from them! Saved me about $200.! Good luck....Tom in SC

Unplug power to refridg/freezer. Removed the screw in rt. rear bottom of ice maker to remove. After removing slightly, unplug pigtail. Remove ice maker completely. Remove large square cover from left side to expose motor. Remove screws to remove motor. Replce with new. Replace ice maker to freezer, plug pigtail back in, put screw back in rt rear bottom, plug refridg/freezer back into power source. Ice was making in about 2 1/2 hours.

Removed Ice container; Removed two screws from housing around shaft; Pulled old shaft from freezer door; inserted new shaft in freezer door; replaced housing around shaft; replaced and tightened two screws securing housing; returned ice container. Tested by activating ice dispenser. It worked like new.

I purchased the part and put it in,

First, let me say that PS was unbelievably fast in getting the part to me ... Extraordinary, in fact. Unfortunately the new part was not the same dimension as the old one ... the four plastic arms that extend through the wall from the refrigerator side to the freezer side and secure the part in place measured a full 1/4 inch shorter than those on the original part ... Even with much effort and a few choice words, it was impossible to get the arms to clip into place ... It wasn't,t even close. So, we used our fine-toothed Swedish saw to take off 1/4 inch of the large part of the styrofoam "housing" so that the arms would extend farther into the freezer side ... Even then, it was difficult to get the arms clipped into place. If the part had been the proper dimension, it would have been a 15 minute job - just remove top two shelves from both sides and move ice maker out of the way ... Just need a nut driver to remove two screws from fridge side to get the two cover plates off and one screw from ice maker ... Push part from freezer side to fridge side, pull wire plug off old unit, plug into new unit, push unit in place on fridge side until arms click in place, replace ice maker, cover pieces in fridge, and shelves. Unfortunately, we didn't get a part that fit. Unfortunately, after all of that agony, our problem remains. We had replaced the bimetal defroster first, which also was delivered quickly. It was different from the original, but it fit and was easy to replace. Next we'll try the thermistor! Incidentally, I agree with an earlier reviewer ... Kitchenaid is junk - not the same since Whirlpool acquired it ... Same with Maytag, in my opinion. Thank goodness for Partselect.com!