1068490286 Kenmore Refrigerator - Instructions

First, I removed the two thermostat knobs, then the snap-on plastic cover. Then, I removed the 4 screws holding the housing for the timer, thermostats, etc., and dropped it down enough to remove the timer and the wiring harness going into it. Installing the new one was the same process, in reverse. Quite simple!

Removed the old timer from the housing. The replacement came with good instructions. I followed the instructions corresponding to the color wires in my unit. The first time it was installed, the fridge did not come on and the temperature rose after a couple hours. Looked at the part and realized the defrost cycle must have kicked in. Needed to slightly turn the gray slotted part to initiate the timer so it would stop the defrost and start the fridge. That did it! It must have advanced the timer so it could accumulate run time. Whole repair saved us $3000 in a new fridge.

After spending $250 on repair by calling appliance repair professional who changed relay in the fridge, the problem was not solved. I had to manually turn the switch off and on again to make sure my fridge would maintain its temperature. I read some similar problems on this web site, watched instalation video and decided to give it a try. Part came in very quick and it took me (female) 45 minutes to install the new part and refregirator worked like a champ. I would never call professional again until I try fixing the problem myself.

The repair video was a great help in this specific repair and matched my refrigerator model exactly. The only issue was an apparent design change in the thermostat that I received. The location of the electrical leads has changed. It might be worth mentioning this in the video. Polarity is not an issue in this case, but if it was, it would be worth noting in the video. So far the refrigerator has been operating normally.

The compressor immediately started when I plugged the refrigerator back in. Around 24 hours later the freezer compartment was at 0 degrees, and the refrigerator was at 35 degrees.

Removed old thermostat and replaced with new one. The video link in the shipping email was great - really detailed even though it was a simple fix.

First defrosted it to makes sure all Air flow was opened. Tested the Defroster heater with omh meter, it was OK. Found the location of the defrost timer on the online diagrams. Used nut driver to remove cover.
Replaced timer. The hardest part was decieding how to wire it up, tis was a universal kit and depending on how it was wired as to how often the defrost ran. The firt choice was every 8 hours. Since this was going to be opened often, I picked that one.
Plugged it with in 24 hrs freezer wall mesured -5 and the fridge was at 30, so had to warm it up a bit.
Now all complaints gone, Ice making has been doing better also.

My fridge was not cooling properly as I would have to tap the thermostat at times to get it to kick on again. Ordered the temperature control thermostat from this site t and watched video on how to install. Not hard at all and did it in under an hour. Fridge is working like new..

Ordered shelf support stud kit. Product was promptly delivered, and contained the parts as shown on website. Took longer to open the package than to replace the missing shelf support bracket. No problems. Would order from them again.

Determined that compressor was not running, after researching problem on another site they recommended i try the condenser moor fan or motor, the defrost thermostat or defrost timer. . I was not satisfied with their recommendations. If I had tried their recommendations i would have likely gotten frustrated and spent upwards of $3000 to replace the 22 year-old hand me down unit. Thank you Parts Select for properly diagnosing my relay failure saving me a ton of money.

Removed old switch and installed new - but did not solve problem

Removing old stud was difficult. It will not stap or pull out. Had to cut it off with a Dremel tool, then drill into the center of the old stud and pull out the pieces with needle nose pliers. Be careful, there are 2 metal pins on the side of the hole in the wall of the frid that need to stay there. These are in addition to the 2 metal pins on the shelf support stud. New stud popped right in easily.

I followed the procedures that others described that had the same problem,very handy

One front roller was flat on one side. Decided to replace all rollers at same time. Placed shims under unit and removed mounting screws for one front and one rear roller. With new rollers in place, I was able to level the refrigerator side to side, but unable to do so, front to back. Left the new front roller in place and reinstalled the old rear roller. Have decided to replace refrigeratorin the near future. This is one of my few repair failures!

I took apart the thermostatic switch and cleaned the contacts (noticed carbon or corrosion dust beneath the switch). I installed the old switch back in the fridge until new switch arrived. This seemed to solve the problem. I ordered a new thermostatic switch and a new defrost timer since these two items if defective, cause similar symptoms to my problem. I replaced both items and the refrigerator has worked normally since. Replacing both parts was straight forward process. Hope this helps.