25370309613 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- timothy from georgetown, TN
- Parts Used:
- 242252603
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Water Valve was leaking water and not making ice
I unplugged the fridge and unscrewed the back cover,unscrewwd the two screws holding the water valve in place and the water line to the ice maker and the electrical connection and install the new water valve,then buttoned everything back up and plugged the fridge back in and it is working great,making ice as normal.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bryan from Minneapolis, MN
- Parts Used:
- 240535101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Missing door rack
Just snapped them into place without any problems! The parts were exactly what I was looking for.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ANGELA from MEBANE, NC
- Parts Used:
- 316538904
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Refrigerator Light bulb went out
I replaced the bulb using my hands to twist the bulb in the socket located at the top of the refrigerator.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jennifer from BUFFALO, NY
- Parts Used:
- 242252603
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Icemaker stopped making ice and i knew it wasnt the mechanism since I could hear that working when I unplugged and plugged the unit back on.
I found a couple of videos online of a similar product fix to get a lay of the land. When I got the part, I unplugged the unit and turned off the water. It was easy to take off the back panel and remove the old water intake valve to swap it out for the new one. Once I attached everything again I could see that the valve was taking up water but it didnt seem to be going all the way to the icemaker. I gave it some time and by the next day, there was fresh ice!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- amy from SOMERVILLE, MA
- Parts Used:
- 240312421, 5304507146, 240311303
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Door sagging, creating a gap to let in condensation
You tube is my best friend for DIY repair. I supported the door with wood blocks, removed the bottom bracket and was able to slide the refrigerator door down and out without removing the freezer door. Replaced both hinge bearings and door stop and washer on bottom hinge and slid the door back into place. Door is very light when empty. Fast and easy, door opens and closes smoothly and no problem with condensation anymore.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anthony from LANCASTER, OH
- Parts Used:
- 240535201
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
broken restrained rack
The old one popped out, the new one popped in. As easy as that.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roberta from Port William, OH
- Parts Used:
- 240535101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
door rack broke in half
opened thepackage snapped in place .took all of 3 minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Louis from Damascus, PA
- Parts Used:
- 242252603
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Warter valvr cracked
It was real easy but I still have problem making ice cubs
Fell problem is in the ice maker went it dose make cubs they don,t dump
Fell problem is in the ice maker went it dose make cubs they don,t dump
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Keith from Fort Thomas, KY
- Parts Used:
- 240535101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken lower door rack
Snapped the new rack right into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leah from Tecumseh, OK
- Parts Used:
- 242252603
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
After installing new ice maker water was not running into the ice maker.
Shut off water supply under the sink. Removed old valve and installed new valve. Turned water back on and within a couple hours the first batch of ice made.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Lancaster, CA
- Parts Used:
- 240313703
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
The original part was plastic/and broke
unscrewed to little bolts and installed the new/metal part we got rfom partselect.If we may say.this is a great company to buy from! Fast!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from INVERNESS, IL
- Parts Used:
- 240364503
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Crisper Drawer in Fridge was cracked
Ordered a new one and simply slid it into place
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from SAN MATEO, CA
- Parts Used:
- 316538904
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Repaired Oven Range Light Bulb
The bulb has a plastic clear cover. That cover can just be carefully removed using a screwdriver. It's held in by a metal bracket. After you remove the cover. You'll just need to replace the bulb and then re-install the cover and bracket.
Was this instruction helpful to you?
Thank you for voting!
refer door hinges were lost during the move in to our first home.
The center door hinge was still attached to the refridgerator so I only had to install the bottom and top hinges. I also moved the door handles to the other side so the doors open the "right" way. The hinges were just 2 bolts and 3 screws. Now, just if the repair man from our home warrentee company would show up to fix the refridgerator. It's blowing hot air!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patrick from RICHWOOD, TX
- Parts Used:
- 242252603
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
The fan had stopped spinning. According to the internet it should spin freely if I use my hand, but it wouldn't.
After pulling the fridge away from the wall and opening the paper backing on the bottom, I could see the motor. It's affixed to 3 metal ribs by 3 small screw/nuts. There is also a 12" wiring harness that led to a simple disconnect. Removing the disconnect and the 3 nuts was easy. However, there was no room to remove the motor with the fan attached. Between frame parts, the drip pan below, the ribs, and small, delicate copper tubing that can't get bent, it wouldn't fit thru any openings. So we rotated the motor inside the framework until the blade faced out, then reached in with a pair of needle nose pliers to remove the washer. Removing the washer is easy, it's just difficult to reach. With the washer off the fan was out of the way and very carefully (it was tight) the motor came out. Reverse was the same issue. Motor tight going in, not a lot of room to maneuver fan onto motor, and needed needle nose to tighten washer again. Make sure you tighten the washer before you install the motor on the prongs. Otherwise you need to remove it from the ribs, twist it to face you, then reinstall it on the prongs. Also, I felt I was stripping the nuts into the new motor. Turns out the holes in the motor aren't tapped. i realized the nuts are self tapping once I looked at them. I'm a big time DIYer and this wasn't bad at all. If your motor/fan assembly comes out whole, it's even easier.
Was this instruction helpful to you?
Thank you for voting!