25370309613 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Mordechai from Brooklyn, NY
- Parts Used:
- 240535101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Easy and simple!
had it done in 5 seconds!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- W. Noah from Leominster, MA
- Parts Used:
- 240535101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Kid broke to bottom door rack
This was so easy it took longer to open the door than it did to install the rack. WOW. Nice to see something fits without messing with it. Thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from MARYVILLE, MO
- Parts Used:
- 240337712
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Needed a replacement door for the dairy compartment
It simply snapped into place. No tools required. A very simple repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christina from Essington, PA
- Parts Used:
- 240535101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The original shelf cracked and fell off. No glue or tape would hold.
Just snapped the item into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- francine from brick, NJ
- Parts Used:
- 240535101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replacing broken door racks
Super easy it took no more than 5 minutes to replace the fridge door racks. Starting from opening the box when it arrived to closing the fridge door with the new racks in place. no tools needed, except a knife to open the box.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from HOUSTON, TX
- Parts Used:
- 242252603
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Wrench (Adjustable)
Ice maker not making ice
Pulled unit away from wall and shut off water and unplugged unit. Installed water valve and reassembled, plugged back in and turned on water and checked for leaks. All good. However there is no water getting into the ice maker. The unit itself is going thru a cycle of attempting to make ice and the bail is moving and you can hear the solenoid activate but no water. I have tried to blow thru the tube going to the maker but it seems to be plugged by something. I do not know if there is another valve up there or how to clean it out. Any help would be greatly appreciated.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lorraine from Arlington, VA
- Parts Used:
- 242161202
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
very Simple!
Insert the bottom part of the trim first, then pull up to snap on the top. PartSelect.com is a fantastic website!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Denise from Landover, MD
- Parts Used:
- 316538904
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
light bilb went out
replaced it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Greg from henrico, VA
- Parts Used:
- 241639502
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Socket set
The new motor mount screw holes were not threaded.
I had to tap the screw holes with a 8/32 tap so that the screws would not bind.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Keith from Springfield, OR
- Parts Used:
- 240313703
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Freezer door sagging due to warped hinge
Just block the door up so it doesn't fall off, remove the two screws, replace hinge, and replace screws. My wife could have done it. Metal replacement part is much better than the original plastic that warped from day one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gene from Chesaning, MI
- Parts Used:
- 240313703, 5304507146
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Freezer door sagged & didn't seal properly
Installed Metal hinge(old hinge was plastic) to take out sag of door.(painted the hinge color of refrigerator as hinge doesn't have plastic appearance cover )
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Glen from North Tonawanda, NY
- Parts Used:
- 240535001
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
no heat when drying
Replaced thermo-fuse
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- G V from Bowie, MD
- Parts Used:
- 242252603
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Wrench (Adjustable)
No ice - Replace water valve
TURN OFF WATER!! UNPLUG REFRIGERATOR!! Remove water fittings and electrical connector on old valve. Remove two mounting screws on pump bracket. Reverse procedure to install.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ron from Tiffin, OH
- Parts Used:
- 240535101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Needed a replacement for a broken doo rack
Snapped right in place, no problems at all.
Was this instruction helpful to you?
Thank you for voting!
the racks on my doors had snapped and I needed new ones
I just put them right on. Took about a minute to figure on the right way to put the racks on (push them down from the top, until they snap into place), and it was done in less than five minutes. I was worried that this wouldn't work - I couldn't find the exact item # to replace the racks that had been on there. But it turns out that they are pretty interchangeable - the sub racks that the website suggested worked perfectly for me.
Was this instruction helpful to you?
Thank you for voting!