79571322411 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jane from SHORELINE, WA
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Door switch would not turn on interior refrigerator light.
I had previously watched a YouTube video (do this first!!) on a similar Kenmore model so I knew what to look out for: (1) turned off power, (2) took thin putty knife to slip under outer lip of switch (most screwdrivers are too thick), (3) wiggled switch at front end to release the tab, (4) unplugged from the socket, (5) plugged in new switch, (6) popped new switch back into door, (7) turned on power. Voila !! Super easy. I couldn't believe it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from MINNEAPOLIS, MN
- Parts Used:
- AEQ72909603
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Ice maker quit working
Plug in the replacement ice maker to the socket in the frig, fit the back of the new ice maker into the slot to the rear, attach with 2 screws saved from removing old ice maker. Simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from WHITE BIRD, ID
- Parts Used:
- 4681JB1027C
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Blower motor out on condenser
followed detailed movie from Utube video
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William L from SUMAS, WA
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
light didn't come on when the door was opened
I took a very thin bladed screwdriver and took the old part out -carefully.
The new part fit in quite easily.
The new part fit in quite easily.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from Sewell, NJ
- Parts Used:
- 5218JA1010E
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Freezer frost accumulation
After noting frost in freezer Right rail started to jam. Noted freezer door was closing crooked. Rail replacement resolved issue. It had been frosting up for some time so Rail must have been broken for a while. Check door seals they were not closing flush.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from WILKES BARRE, PA
- Parts Used:
- MCR65017001
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
Decor tray broke
Did repair it yet part came damaged and I’m still waiting for customer service to get back to me for the last week and half so my part came damaged and it’s still not fixed
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- shirley from ONALASKA, WI
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Light switch for refrigerator not functioning
Followed instructions online
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from CURWENSVILLE, PA
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Door light switch, 3rd one I have replaced in 6 years made in China.
Easy install, small screwdriver under back of old switch push out and pull out with small pliers. unsnap the old plug and install new. YOUR DONE
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dean from HILLSDALE, MI
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Replace switch
Read previous tips
Taped off area around switch to protect surface
Used putty knife to extract switch
Used screwdriver to separate connector from switch
Plugged in connector
Pushed switch assembly into opening
Removed tape
Taped off area around switch to protect surface
Used putty knife to extract switch
Used screwdriver to separate connector from switch
Plugged in connector
Pushed switch assembly into opening
Removed tape
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from PENNSVILLE, NJ
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Switch stops working
Replace with new switch. this is the third switch i have replaced in 10 years. the only part, besides a light bulb, that has gone bad. obviously this is a problem with this model for Kenmore, or just poor switch design.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from CLARENCE CTR, NY
- Parts Used:
- AJU73672505
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
water leaking from where line goes into icemaker in back of refrigerator.
The old valve must of had a slow leak and ice built up at icemaker. Make sure you clear ice from line at that point before turning on icemaker.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Philip from Ashland, MA
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Lights didn't come on when door was opened
I have moderate to good mechanical skills, but getting the old switch out was a sizeable challenge. Since this switch suffered some damage during extraction, I was lucky to have ordered a new one to replace it. Reinstall took approximately 90 seconds. PartSelect saved me an expensive service call.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from TONAWANDA, NY
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
bad switch
The 2 minute or so video was not exactly matching the model that we had but the instructions were very good and important. The switch was a little difficult to get out from the side of the refrigerator.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Calvin from Northome, MN
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Light quit coming on when door opened.
Unplug from wall receptacle. Pry switch out with screwdriver while pushing on inner tab. Then disconnect electrical plug.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alice from PHILOMATH, OR
- Parts Used:
- AAP73051305
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The original broke
I snapped in the new one. Took about a minute and a half
Was this instruction helpful to you?
Thank you for voting!