1068480110 Kenmore Refrigerator - Instructions

Forty years ago I serviced air conditioners and all kinds of refrigeration. At that time starting relays were electro mechanical, I hadn’t looked under a refrigerator in a lot of years and was surprised to find out that the new relays were solid state. The defective one had a bunch of broken pieces floating around in the case. I jury rigged a starting cord and confirmed that the compressor would start and looked at running current for thirty or so seconds. I ordered a new relay kit and it worked just right. I’m seventy five years old and it takes me longer to get up off the floor than it took to replace the parts. Your delivery was first rate the parts got here before I finished doing the paint touch-up on the door under the ice maker/water dispenser. Fed ex was easily three to five days faster than the brown truck.

new shelf was installed by placing the clips into the provided slots.

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

the speed of part delivery was amazing. using the instructions, posted on your web site, the installation was quite easy. without the instructions it would have taken much longer. thanks to all.

Watched the video, followed the instructions, took my time and paid attention to what came off where, and viola. Not quite as easy as the guy in the video, but then it was my first time! Bottom line is: it worked. Refrigerator/freezer now maintains temperature exactly as expected, and I saved hundreds. Thank you!

We bought the fridge used and immediately see why it was being sold. But ordered a new thermostat and with Part Select's instructional video was able to replace the thermostat. I should mention it was my first attempt making any repairs to a refrigerator. It was fairly straightforward project.

Remove inside door trim plate. Then removed three screws that held in the light assembly. The only difficult thing was reconnecting the temperature adjustment rod. After replacing this rod you must slide the temperature control slide to midway and this hold the rod in place while reinstalling the light assembly. If I were to do it again it would probably take me half as long.

Working from inside out . Remove left upper tube cover and then vent cover . Remove thermostat tube from around the vent . Remove knobs and front cover . Remove 4 hex screws , drop the whole unit enough to expose the left control rod , remove the rod retaining clip . Gently separate control rod from unit . Take the whole unit to working bench or table . Remove thermostat and bracket . Need to reuse bracket with new thermostat . Don't forget the clear plastic tube you have to reuse that as well . Be careful not to kink the thermostat tube . Reverse procedure , working from outside in . Good luck

Just like the video I watched online at your web site. piece of cake.!!

I followed the instructions shown in the on-line video for replacing the thermostate control. I had difficulty freeing the capilary tube from around the mechanical lever that controls the freezer side vent opening. I had to remove a screw that held the vent lever in place. This is a delicate activity. I was not happy with the way the on-line video delt with this particular issue. Otherwise, the video was right on and straight forward. The problem is fixed.

This was an easy part to find thanks to its universality. The only difficulty was the electric snap-on connection - had to use the old one and tie the wires to the new motor - that was easy. Hardest part was the new screws to mount to bracket weren't long enough. Had to find one in my screw jar to match threads that was long enough. Works Great!!!

1. Unplug the electric plug. 2 Either be in a well lighted place or get a flashlite. 3. Remove all food from top shelf. 4. Remove the knobs from both controls by pulling on them or use pliers to grab the center and pull. 5. Use the thin bladed knife and gently slip the knife under the thin plastic panel that covers the two controls and pop it off. 6.Go in back of the control panel and remove the two hex headed screws that holds the panel onto the roof of the refrigerator.7. Locate the right hand control, and use a philips screw driver to remove two philips screws that hold the temperature control body in place. and remove the wires from the terminals by pulling them with a long nose pliers.8. Locate the white panels that cover the thermostat sensor and remove the screws holding them onto the frig body. slip the long thin tube out of the plastic piece it is formed to fit.9.Draw on paper the shape and measure the deminsions,of the long thin tube. Straighten out the tube and remove the plastic covering it. Now slip that tubing over the new piece.10. Form the tubing into the odd shaped holder and gently place all of the new asssembly against the frig wall and cover with the two white panels that you removed to get to the long sensor tube. 11. Reassemble the controls in the same order you took it apart. Plug the frig back in to the electricity and set the control on 5 and it should run. Watch for a period to hear the unit cycle on and off. You are a genius and have saved at least 150 dollars.

Removed the cover from Thermostate, removed the wires, and screws holding old thermostate, reversed instulation with the new thermostat, pretty simple.

I followed the instructions on the repair video, fridge is working fine now. Thanks!

un-plug the power cord. remove both control knobs. pry off the cover. remove 1 screw on the right and left with the nut driver. remove two screws in back with the nut driver. remove the screw holding thermostat in place, loosen screw holding the left side of the l plate. lift thermostat up and remove two nut driver screws. remove the temperature sensing line from holding device. Remove cover down the side of refrigerator and the cover over the sensor (in back corner) carefully remove the sensor line. Carefully bend the sensor tube into the shape of the removed part(do not kink)install the new part in the reverse order of removing.. Use flat blade screw driver to press sensor line into the snaps. This was one of the easiest repairs I have ever completed.