Models > 79572303210 > Instructions

79572303210 Kenmore Refrigerator - Instructions

Jump to:

All Instructions for the 79572303210
31 - 45 of 65
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
CONNIE from YORK, PA
Parts Used:
ADX73350633
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
The gasket was torn and leaking cold air.
Pulled the old gasket out.l. Started at the top left corner of the gasket and pushed the Corning in tight and push the gasket in to the other corner down the right side th the corner, across to the left bottom corner and up the right side to the start of the beginning. Very easy installation.

Delivery was fast. Satisfied with part select.com. Spoke to a representative in customer service and she checked to make sure I was ordering the correct part. Very satisfied with your service.
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Michael from MONTGOMERY, AL
Parts Used:
AGU75188619
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Spring broke on Mullion
Watched the video. Took the screws out, unplugged the connection and slid mullion off. Then plugged the new one in, slid it on and attached the two screws.
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
shirley from ONALASKA, WI
Parts Used:
6600JB1010A
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
Light switch for refrigerator not functioning
Followed instructions online
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Michael from TONAWANDA, NY
Parts Used:
6600JB1010A
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
bad switch
The 2 minute or so video was not exactly matching the model that we had but the instructions were very good and important. The switch was a little difficult to get out from the side of the refrigerator.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Bob from LIBERTY TWP, OH
Parts Used:
AHJ73130001
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
roller was missing in freezer upper drawer
easy, just lift the drawer and insert the roller assy.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Sidney from ENDICOTT, NY
Parts Used:
6600JB1010A
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
The switch became intermittent - Possibly a poor designe
Used a small screw driver inserted into the front of the switch (facing the front) and pried until the switch was coming out. When out, I removed the connect harness and replace the switch with a new one.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
JON from OJAI, CA
Parts Used:
6600JB1010A
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
INTERIOR DOOR ACTIVATED LIGHT SWITCH QUIT WORKING
1. Unplug the refrigerator (to avoid shock) 2. With one screwdriver pry open the switch on the side facing the door to a gap of about 1/8 inch 3. Insert a second screwdriver into the gap to press the plastic tab back slightly and this should release the part. 4. pull the part out and unplug it, you may have to pry back some small tabs on the sides, 5. Plug in the new switch 6. plug in the refrigerator the light should come on, if not tighten the connection 7. Insert new switch back into its slot, it should snap in place. Done!
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Richard from IMPERIAL, CA
Parts Used:
AGU75188619
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Broken spring on flapper door
Unplugged the frig and removed two phillip screws on flapper door of left door... Unplugged the electrical connector and removed flapper...
Picked up new flapper and snapped electrical contractor together... Slid new flapper bar into place and inserted two phillip screws... Job complete in 15 minutes...
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Philip from Ashland, MA
Parts Used:
6600JB1010A
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
Lights didn't come on when door was opened
I have moderate to good mechanical skills, but getting the old switch out was a sizeable challenge. Since this switch suffered some damage during extraction, I was lucky to have ordered a new one to replace it. Reinstall took approximately 90 seconds. PartSelect saved me an expensive service call.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Calvin from Northome, MN
Parts Used:
6600JB1010A
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Light quit coming on when door opened.
Unplug from wall receptacle. Pry switch out with screwdriver while pushing on inner tab. Then disconnect electrical plug.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Charles from CURWENSVILLE, PA
Parts Used:
6600JB1010A
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers
Door light switch, 3rd one I have replaced in 6 years made in China.
Easy install, small screwdriver under back of old switch push out and pull out with small pliers. unsnap the old plug and install new. YOUR DONE
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Dean from HILLSDALE, MI
Parts Used:
6600JB1010A
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Replace switch
Read previous tips
Taped off area around switch to protect surface
Used putty knife to extract switch
Used screwdriver to separate connector from switch
Plugged in connector
Pushed switch assembly into opening
Removed tape
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Robert from WARREN, RI
Parts Used:
AGU75188619
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Spring in the plate front assembly broke. Door plate assembly would not move into correct position, preventing door from closing.
Followed Youtube video provided on the PartsSelect Website:

https://www.partselect.com/PS12374439-LG-AGU75188619-PLATE-ASSEMBLY-FRONT.htm?Inventory=12374439&SourceCode=20&SearchTerm=LFX28979ST

Made installation of the new part a piece of cake. Easy peasy!! Took less than 10 minutes.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
JANET from GRAND JCT, CO
Parts Used:
AGU75188619
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
The spring on the mullion was broken so the mullion would not open to seal the other door.
I am a73 year old woman. If I can do this, anyone can. Super easy. Just watch the online video.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Jesse from Pella, IA
Parts Used:
AJU55759303
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Wrench (Adjustable)
Not making ice but could hear the solenoid trying to work
I turned off the water supply. Took off the access panel at the bottom of the fridge. Disconnected the waterlines from the valve. Remove the screw hole in the valve in place install the waterlines on the new valve attach the new valve to the refrigerator, reinstalled the back panel turn on the water And it made ice.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the 79572303210
31 - 45 of 65