JFC2290VTB4 Jenn-Air Refrigerator - Instructions

Lower the filter bottom housing to gain access to the filter. Unscrew the filter and install the bypass cap. Secure the lower filter housing to the top assembly.

Popping out the broken switch was easy once I was able to see how the new switch part was engineered. The switch was made to be replaced, having a simple tension hook on the bottom of the switch which needed to be depressed to pull the switch out of the cabinet. Once pulled out, there were modular plugs for the power line that were easy to pull off the broken switch and plug into the new switch. Pop the new switch back in and VOILA, the lights worked again! Thanks to part select's good diagrams of the actual model of my refrigerator, it was very easy to hone in on the exact part I needed. I did notice one problem with the order as the correct series for the part was displayed earlier in the process, but had the wrong series later in the process. However,. I trusted the system and the part is for the right series and fit well (an exact match, down to the color). Thanks Part Select, I would definitely use you again.

It is simple, unscrew the old screw in the new one.

Remove the crisper baskets, Hinged lid, Glass shelves, support bars, and to make it easier - the door bins.
There are no screws on the end caps for this model of fridge, unlike some YouTube videos you might see.
There's a release catch nearly in the middle of the cap. With your index finger, press down on the tab, to release the catch, while lifting the front of the end cap. The end cap should lift up and away from the side wall of your fridge.
Be careful to then rotate the entire assembly - in the case of the right side end cap - towards you, so that you can disengage the tab on the crisper drawer temp controller, that fits in the back wall of the fridge.
Once you've unhooked the control rods to the crisper temp. control, you'll need to remove the crisper drawer runners.
Again - on this model, there are no screws. The runners just slide out from underneath their retaining plastic tabs. Slide them towards what would be the front of the fringe if they were in their natural position, they clear the retaining tabs and become free.
The control rods need to be re-attached on the new end cap.. just take your time click it between the various plastic tab.
Then insert the end tab of the crisper temp control in the back wall, rotate the entire assembly 90 degrees, so the end cap is aligned with the slide wall, and lower it into position until the retailing clip clicks into position. Congratulations, you've replaced your right side end cap!
Then reinstall all the supports, shelves, bins etc. and you're good to go.
Good Luck!

So far haven’t done the repair and probably will give up. This issue is discussed in frequent questions area of your web site. Steve’s video needs to be updated to discuss what to do with end caps that are snapped, rather than screwed, in. Before decided to DIY, I looked at video. Video job is easy. Steve showed it was easy, but video end cap has screws. I figured mine did too and so ordered the part. When placing order, rep. and/ or web site should point out issue as now that look at item on line can see no screw holes. As your instructions note for my issue, if can pry old unit off, challenge is to recall where everything that drops out goes when replacing. Because I’m stubborn, will probably try one more time, but likely will fail to swap out old for new end cap. Warning: screwless end cap replacement is not easy.

Removed the top door hinge cover.
Remover the four 12mm hex screws.
Lifted empty door off bottem hinge support.
Removed old door closure.
Put some silicon lub on the new closure and installed.
Reversed the removal steps.

But this did not fix the problem. Will have to remove the door and inspect the inside of the door's lower hinge assembly.

pop open, unscrew quarter turn, screw new one in quarter turn, pop shut. duh

followed the instructions provided and that's it!

Very simple. Matched female plugs with respective male color coded prong; pushed together then inserted unit in slot of freezer sidewall and rotated into position...job done.

Removed pantry drawer and both crispers. Removed glass shelf. Removed both support bars. Using my thumb, pressed into the square openings in pantry cap. That snaps the cap loose from side of the fridge. Removed l-shaped assembly from fridge. Photographed the assembly with my phone camera so I could reconstruct the assembly. It is very complicated reassembling these parts. Reassembled these parts onto replacement part. Inserted tabs on cap assembly into slots in side and back of appliance. Replaced support bars, glass shelf, crispers, and pantry drawer in that order. Slid pantry lid onto plastic prongs at either end of the drawer. If new prong is too long, slice tiny section off with serrated knife and slide lid back into place. Job well done!

Icecubes came out half-way, and refrooze. I figured out, that the melter does not work (HEATER in the icemaker) Voltage measured 105V no load. Studied the Internet, and folloved an advice: shorted the back wire and the blackwire with white stripes.these go to relay contacts. It seems, that the relay contacts are no good on Infrared receiver boaed. I turn off manually the icemaker, when needed

First I removed the six screws from the cover. I then disconnected the two wires and pulled the small motor out with its base and removed two screws that hold it in place. I then changed the old one for the new one and set it back in its place. I then set the cover back and turned it on. I was happy again.

I called the installer of my filter unit and he told me that often, thhe fridge filter is the problem. Like magic it worked

Received the union I ordered, then discovered that the tubes were different sizes, so I had the wrong part. I had read elsewhere that it was necessary to trim the two ends of the tubes with a box cutter to stop the leaks - I did this, and the leaking stopped. I was then able to go to a local hardware store and get a 5/16 to 1/4 union and replace it. The leaking is stopped, and the water supply in the door is now working like new. No problem with partselect, but I did buy a caliper so that I can check tube diameters if I ever have a similar problem! This is a great site to find instructions - well worth the time to search!

1) Remove Deli Center drawer and lid 2) Remove the two Crisper Drawers above the Deli Center 3) Remove the glass shelf above the Crisper Drawers. 4) Remove the front and brackets that held the glass shelf. 5) Remove the broken end cap by sliding it upward off the brackets that hold it to the side of the refrigerator, 6) Slide on new end cap. Replace the other parts in reverse order of removal. You will probably want to clean the parts you have removed before reinstalling. Easy- peasy.