JFC2290VEP8 Jenn-Air Refrigerator - Instructions

I got really tired of taking food out covered in icicles and stabbing a huge block of ice out of the bottom. Turns out all he needed was a little wheel with cogs and I looked up the sticker model number on this site and clicked the part of the fridge. So simple, wish I would’ve done it sooner.

I made a temporary repair by drilling the old blade plastic hub and put a small screw in it to hold it on to the shaft until the new blade arrived. The new blade came in within the two days I needed before Thanksgiving. I removed the old and pushed on the new. There were 8 screws on the back guard and two to hold the motor on. It was a snap.
Thank you PartSelect.com The wife is very, very happy now, we had 51 coming over for Thanksgiving. :)

I changed the bulb but it still didn’t work. I ordered a bulb holder and replaced it and it works properly now. It was an easy repair, remove the bulb, gently pry the bulb holder out with a screwdriver and snap the new one in.

It was useful that under the description of the part in the catalog, it showed that this part was often used to repair this issue. The service was great and the delivery was fast.

Remove the grate at the back of the refrigerator. Remove the existing drawn tube. Replace the exiting drain tube with the updated drain tube. Check to see if water was draining properly. Replace the grate. Sit back and have a beer.

Open the existing cover and carefully with the thumb and index fingers, pry the cover at over the left pin and remove the cover. Place the replacement onto the right pin and pry the left placing it over the left and you are done.

Opened the boxes and hung them in the door just like the old ones

Very simple A) watch video B) Go carefully so you don’t break another plastic part. Took all of about 20 minutes, fit perfectly and works like new.

Remove the Veggie shelf top. Remove veggie tray. Pull the clip on the center of the left panel - lift and pull forward.
Install new panel by inserting the two guide pins at the rear of the frig and move the panel to a 45% angle so you can install the veggie lid pin into position before moving the panel down into the secure position. You will hear the clip seat into position. If you do not do this I am not sure how the lid pin can be installed without breaking it.

Had to replace both sides- very easy repair no tools needed.

Unplugged wire plug, removed mounting screws and removed ice maker. Installed new unit by reversing steps--

Used a 1/4" nut driver for the project install, just one note when installing the water feed into the new inlet valve make sure it is seated properly, look for the indicator mark on the water feed. Very easy installation!

I watched a 5-minute YouTube video ordered the part. It was delivered fast and it took me about 30 minutes to put it on.

Followed some online videos. The replacement part actually matched exactly what the videos I found showed. It was my refrigerator that was slightly different where the unit would mount/screw into. The old unit had a bracket which easily attached to the replacement part. It is less than a 1 hour repair for sure. But it took me a few minutes to figure out the bracket adapter. Plus I forgot to seat the ice maker shut off bar and had to disassemble some things again to get in there to seat it properly. Part was shipped quickly and securely !

No product was sent in the box for the shaft I received an empty box from them cannot perform any repairs because I got no product from this company. Called customer service said due to Covid no customer service available when online and receive no customer service no refund no product no help

Unplugged refrigerator,cleaned out freezer.Removed shelves in freezer compartment(that took some figuring to unlock sliding sheves)Our freezer is on the bottom.Removed four screws from back cover to expose fan,removed screws and attached wires.Carefully opened plastic clips after pulling fan off shaft.Replaced old motor after reattaching rubber seals.Closed clips to hold motor and placed fan back on shaft.Reattach wires and screws. Put cover back and replaced shelves.Plugged in refrigerator and wallah refrigerator part was cold again!