JFC2089HEP13 Jenn-Air Refrigerator - Instructions

I called the installer of my filter unit and he told me that often, thhe fridge filter is the problem. Like magic it worked

Used exploded drawing from Partselect to get an idea how to remove the keyboard housing. This was the hardest part since it "snaps" into place in addition to a couple screws.
Once I got it apart, I figured it was either the electrical control board or the keypad itself , so I ordered both. I also ordered a new keyboard housing since the keyboard is stuck to the housing with strong adhesive, so this must be replaced with the keyboard.
When I recieived the parts, I tried just replacing the keyboard, and this worked. I adhered the keyboard to the new housing, put it all back together and the fridge works great now. I returned the electrical control board viw USPS priority, and got a refund within 1 week of sending it.

Thanks!

Followed the YouTube video linked to the Compressor Start Device and Capacitor I purchased. The repair was just as easy as the technician in the video said it would be. Removed the back panel, remove the clamp, worked the Compressor Start Device and Capacitor off the electrical prongs and replace it with the new one. After I reassemble the refrigerator, it was fully operational. Very easy to do and only required a few tools.

Once I got the right part the repair was quick and easy. All I had to do is get the old part off with a screwdriver and curved needle nose pliers and the old part came right off. The new part went in just as easy. Quick and easy. Less than 15 minutes.

I simply replaced the shelves and drawers

Could not figure out why this was happening suddenly. Then remembered I had recently changed the lid to one I had stored for over two years in the garage. They had sent me a replacement lid when the unit was less than a year old because the origianl had a crack in the clear section. Noticed it seemed a little warped. Thought I would replace it to see if that solved the
problem.
We had to replace the side panel of the draawer because the warped lid had broken the peg off of one side. I didn't want that to happen again.
The new lid did the job....This company is the only one I will use in the future for my appliances. Very easy to find parts and the pricing was better.

It was so easy!

Thanks for the rush to my home on the part.

I just unscrewed the plate that locks in the light switch (screwdriver) and unplugged the old faulty part and plugged in the new switch, screwed the cover back on and I was done!

Easy!

And I am not Mr. Fix-it!

Unplug ref then remove lower(freezer) panel plus trays and thermistor’s cover/holder then remove the evaps cover. I found the evaps all frozen up. Cut and remove old thermistor, strip wires 1/2 inch then cut the new thermistor wires to length and strip 1/2 inch, use the enclosed insulated crimp type connector and put back everything in the reverse order. It works great afterwards.

The lining of the ice mold (Whirlpool) started flecking off (black flecks in the ice cubes), so I decided to replace the mold.
Loosen the two 1/4 inch upper nuts and remove the lower nut to remove the ice maker from the freezer. The hardest part was getting it unplugged. I used a small blade screwdriver to release the catch on the connector and pull it out.
Remove the ice maker front cover. If you have a skinny enough phillips screw driver, there are two deep set screws through two holes on the lower portion of the control module (otherwise, remove the three screws on the controller, unlatch the shut-off arm from the control module, and separate the controller to access the mold screws). Unhook the shut-off wire from the end of the tray. Unscrew the two screws holding the mold and remove the mold.
Remove the plastic hardware from the old mold and install on the new mold.
Attach the new mold on to the control module.
WARNING WARNING WARNING!!! The mold I bought already had the alumilastic on it for the contact point to the thermostat. When I installed it and tightened the screws, the alumilastic was dried out, didn't squash down, and dented the bi-metal thermostat on the controller, ruining it. I had to buy a new thermostat. Be sure to check that the alumilastic is pliable. If not, take it off and buy some fresh to put on there.
Re-install the ice maker. It took a while to get the first batch of ice because the ice maker was at room temperature and I had the freezer door open for several minutes. So the freezer had to get cold and the ice maker had to chill down. Once everything got cold, it started making ice again.

turn off water and unplug fridge. remove ice maker bottom mounting screw. just loosen the 2 top mounting screws. unplug wire harness from back of fridge. remove old icemaker from freezer compartment. once removed, salvage square endcover and reinstall on new maker. unfasten wire harness from old maker and reinsatll on new one. reinsert thermal wire in new ice maker holding bracket. remove second wiring bracket and reinstall on new maker to hold remaining wires (not mentioned on "how to-" video). remove old ice maker on/off bale and reinstall on new one. remount new maker to top mounting screws, reinsert harness plug into fridge. replace bottom screw,

1. removed both bottom crisper drawers
2. removed glass shelf under crisper drawers
3. removed shelf support pieces
4. removeded snack drawer
5. removed left slide rail using phillips screwdriver (2 screws)
6. removed LH end cap using socket wrench (3 screws)
7. attached new LH end cap
8. attached slide rail
9. installed glas shelf supports
10. installed glas shelf
11. install bottom crisper drawers
12. install snack drawer
13. install snack drawer top

total time was less than 15 minutes

The front had to be removed from old drawer a put on new one

Removed the three screws that held part, lifted and removed old part and replaced with new piece.
Couldn't have been easier. Saved me the $100 the repair man quoted me. Cannot believe it was so easy and the
part was soooo affordable! Thank you very much for the speedy delivery. It came within days of my order.
I will use your service again for sure!
Thank you!
Allyn Rosenzweig

you need to take the deli drawer out, make sure your flat head screw driver is large enough for the head of the screw as screwing into the plastic is a bit difficult. Other than that there are 2 screws and its pretty easy.

(1) Slide out appliance and remove power source. (2) Removed lower access cover on rear of refrigerator. (3) Disconnected plug to the condenser fan motor. (4) remove blades by pulling gently forward (5) remove mounting hardware holding the fan motor (3 screws) (6) motor is now free and new motor can be installed