JSD2789HEW Jenn-Air Refrigerator - Instructions

I removed the water filter located in the refrigerator and replaced it with the bypass plug. The ice cubes and the water dispenser work properly . I am pleased with the outcome especially the price was only $15 and less than 5 minutes of my time. Maytag recommends replacing the water filter every six months at $40 a filter. One can see how this will add up in time. Eventually I am installing an after market water filter in line prior to the refrigerator.

the main water valve was leaking causing the water under the frig. But the double out let valve was not holding causing a ice build up in the ice bin. The repair was not complicate you take back cover off turn off water. use the nut driver to unbolt the valves from the frig with frig unplugged use screw driver to remove the power plugs from valve. use flare nut wrenches to remove main water line.push on plastic retainer rings to remove plastic tubing. remove valves from bracket and then reinstall in reverse order.

turn off water and unplug fridge. remove ice maker bottom mounting screw. just loosen the 2 top mounting screws. unplug wire harness from back of fridge. remove old icemaker from freezer compartment. once removed, salvage square endcover and reinstall on new maker. unfasten wire harness from old maker and reinsatll on new one. reinsert thermal wire in new ice maker holding bracket. remove second wiring bracket and reinstall on new maker to hold remaining wires (not mentioned on "how to-" video). remove old ice maker on/off bale and reinstall on new one. remount new maker to top mounting screws, reinsert harness plug into fridge. replace bottom screw,

It was easy breezy!! I felt like an empowered woman that I did it myself. I simply removed the old shelf supports with a screwdrive and inserted a screw thru the new supports and screwed them in.

1/4 turn of old filter. it popped out. Inserted new filter, 1/4 turn and it clicked in. Piece of cake. I'm a freakin' genius.

Unscrewed old filter and screwed in new filter.

(1) Slide out appliance and remove power source. (2) Removed lower access cover on rear of refrigerator. (3) Disconnected plug to the condenser fan motor. (4) remove blades by pulling gently forward (5) remove mounting hardware holding the fan motor (3 screws) (6) motor is now free and new motor can be installed

First I rolled the fridge out and unplugged the power cord. I then removed the ice bin. There was one screw to the left under the ice bin rack holding it in. After removing that screw, I could pull the rack out far enough to disconnect the electrical connector. You have to squeeze the wings b-4 you can pull the connector loose. I put the rack on the countertop, removed two screws and the solenoid with plunger came out. I replaced the old solenoid, put everything back together, and realized I probably just saved myself $300. My Wife thinks I'm a Hero again. It works fine now.

Removed the screws holding the housing inplace pulled and threw away than went to install the new drive motor but the screws were of a different thread so reinstalled the old motor and put the housing and bucket back together. after thawing out the water fill tube put it back into the cup-water fill and put clamp back in place. system is performing like brand new.

Discovered ice door tab was broken. Ice door out of position.
Disassembled door dispenser, pretty easy, two torx screws on bottom, two on upper part of unit. Slid unit up slightly, it sets over two studs on the top. Unplugged wire connector, set aside unit. Looked on internet for a replacement part. These folks had the easiest to use web site. Found the part, ordered the part, received it next day, but only ordered the least expensive delivery method, since we are both in Florida it worked out well.
I did not know when I ordered this part I would get it this quickly. Because cold air was pouring out of the hole left by the removal of the ice door, I put wide painters tape over the hole on the inside of the freezer door. This greatly reduced the flow of cold air.
After I received the part, I clipped it in place and reassembled the unit, it did not work. The solenoid that moves the door just hummed like it was jammed. I took it back apart and realized that I did not get the bracket that moves the ice door reattached properly. After I made sure the bracket was properly attached, i reassembled the unit and it worked great. It actually took longer to type this description than it did to do the job.
Good Luck, Mike

1 screw remove assembly. Unplug cable harness and remove old cover and wire arm. Replace cover and wire arm and attach wire harness on assembly end. Re attach using screw removed in first step. Plug in wire harness. Making ice within 30 minutes.

change light bulbs

Well folks I put up with an ice burg all summer when I really should have took the time to fix it. You know how it goes though. You get so busy you just put it off.
Well don't put this one off because this is just how easy it went.
I came home one evening and wanted to make a drink to relax but that big glob of ice was there waiting for me. I took a crewdriver and beat it down so I could pull the catch basin out. Having looked it over for a minute I grabed a nut driver and took three of the screws out that held it in. I unpluged the wire and bingo it was out. Maybe five min. had elasped.
After taking the unit out I notice how the non stick surface was coming off of the tray and that explains the black pieces that were getting into my ice.
Getting the model number off the back of the fridge and writing it down I went to my trusty lap top and did a quick search for a ice maker for my Jenn Air refrigeraton and blamo...! Part Select came up and I put the part number in their search engine and bingo again there it was, my part.
One quick order and in three days it was right there by my door when I got home.
Now i'm so excited. I went into the house and didn't even chage out of my dress clothes. Within five minutes it was in. Now I just had to wait for the timer to do it's thing and sure enough, I awoke the next morning to a whole tray of beautiful ice cubes. Wow no more ice burgs.
The moral of my story is I spent so much time hacking out that glob of ice and for fifteen minutes of my time, I could have been siping on cold ones by the pool but now old man winter is pressing down on me and I guess a lesson learned was a lesson earned. Fix it!

I followed the instructions supplied by others on your site .They were right on. The repair was simple with the instructions. The service was absolutely superb. I ordered the part one morning.
The next morning Fed EX delivered the part to my door. I will use your site for parts from now on.

The factory installed fill tube was formed and molded, hard plastic. Nothing like the replacement part or the one depicted in the install instructions.To remove it, I had to grip the exterior water tube module with a pair of Visegrip pliers, twist and pull as hard as possible, to expose a section of fill tube. I then had to cut through the tube with a hacksaw to remove the module and flange that secure it to the access hole. From the inside, I removed the ice maker and fan shield to expose the remaining section of fill tube. Using a section of copper pipe and a hammer, I was able to drive the tube through the back wall of the appliance. Fitting the new tube was easy. However, it is too short to reach the fill cup. I fashioned a section of the old tube to create an extension which I inserted in the new part. And, much to my surprise, it actually works!