JBSS48E22L00 Jenn-Air Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Howard from Boynton Beach, FL
- Parts Used:
- 350930
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Both outside door handles turned very beige
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Davis, CA
- Parts Used:
- W11396033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light Switch Was Faulty--Failed A Few Months After Purchase Of The Refrigerator
I had several times tried to get the old switch out but with no success. Ordered the "repair kit" and followed directions for removing old switch (there is a plastic spring clip on one side). Easy to unplug the old switch, plug the leads into the new one, snap the new one into place. Took about 5 minutes total--piece of cake. I wish I'd thought to try this years ago when the old switch began to fail.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roger from Hampton, CT
- Parts Used:
- W11629974
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
None
Watched the video it was right on, no problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from Williamsburg, VA
- Parts Used:
- W11629974
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Ice maker was not working (door ice container)
1. I first confirmed that the problem was a bad Infrared Ice making control board (Watched flashing of red light on right side of freezer - solid light would not occur when holding flap on left side of freezer). 2. I unplugged refridg,3. unscrewed both sides of the control unit and disconnected wire clips to the electronic boards. 4.popped in new Boards on both sides and connected clips onto each board. 5. Screwed the boards and covers to walls of freezer. 6. Plugged power back into wall and checked Red light again (when holding flap in, a continuous red light verified it would work). closed freezer and shortly ice was being made. Simple process. (careful using Screwdriver to help take wire off of boards - a small clip holds wire clip on - you need to stick screwdriver into back of clip while unconnecting). Easy and my ice worked perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from princeton, WV
- Parts Used:
- W11629974
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Ice maker was not making ice
used the video on your web site. also read the overview made things really simple
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Greg from Escalon, CA
- Parts Used:
- W11629974
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
No ice after replacing the ice controller...
I read the other replies and decided to replace the boards. It worked!!!! Ice right away!!! I would have only needed to chafe that if I didn't muscle the ice maker arms around in frustration and brek it!!! This website is great!! Parts came fast and accurate !!!! Thanks parts select !!! Another satisfied customer!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Connie from Mt. Vernon, KY
- Parts Used:
- W11629974
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Ice Maker had stopped making ice
Unplugged refrigerator, took panels off each side of ice maker, unplugged bad components and replaced with new ones. Returned panels, plugged refrigerator back up. The ice maker began making ice almost immediately.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mahlon from Washington, DC
- Parts Used:
- W11629974
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
icemaker didn't work
Removed and installed new control boards
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joanne from Bourbonnais, IL
- Parts Used:
- W11291138
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Light switch broke
Pulled out old switch with needle nose pliers, unplugged old switch and plugged in the new one and snapped back into place. Very easy to repair. Took less than 10 minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michalynn from Powder Springs, GA
- Parts Used:
- W11396033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light switch broken off by container in freezer
Pried out the old switch with small screwdriver, popped in the new one and tah-dah!! ..the light came on. While I was at it, I cleaned out the freezer :). I cannot begin to imagine what a repairman would have charged for this.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- howard from bruceton mills, WV
- Parts Used:
- W11629974
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
icemaker inop would not harvest
easy,remove old parts installed new parts,icemaker started working properly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from Griffin, GA
- Parts Used:
- W11291138
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door light switch broken
It took less that 30 seconds to pop out the old one and less that 30 seconds to install the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from Powell, OH
- Parts Used:
- W11629974
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Power Surge fried the ice maker control boards.
I was ready to spend the $$$ on a repair person when my wife (smart woman) suggested I go on line to see if we can fix it ourselves. I (luckly) found your company and your website made it easy to find the right part plus as an extra bonus you had a video that showed how to switch out both control boards. To top it off, the package came so fast ( the next day - even with standard shipping ) I did not think it was the parts. 10 or so minutes with a Phillips screwdriver and we were back in business. THANK YOU ! ! ! !
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thornton from Highlands, NC
- Parts Used:
- W11629974
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
icemaker stopped working
I did not have voltmeter to test for problem. Internet sites suggested the most common problem is the circuit boards--a sender and a receiver which detect when the ice bucket is full. I could only buy as a pair (about $94). I removed two screws of cover of receiving unit, detached the coupler, replaced the circuit board. Icemaker now works. The sender was obviously still good.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Hebron, KY
- Parts Used:
- W11629974
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
ice maker stopped making ice
research of company website showed parts to buy (per percentage of failure) and how to install those parts I viewed video on installation of parts and did the job, it was a snap
Was this instruction helpful to you?
Thank you for voting!