JFFCF72DKL06 Jenn-Air Refrigerator - Instructions

Followed the instructions in the video provided via email from Partselect
However, the part received was the opposite design of the part removed.
It appeared this could be left hand right hand choice of part. Moreover, the button on the switch that turns the light off/on when door is open/closed was not functional due to the part being the opposite of the part I was replacing. I tested the switch I was replacing and it appears this is not the problem. I think the light socket is the problem. I am 69 year old female and capable of doing small repairs, but limited knowledge of electrical so having to troubleshoot by trial and error. Thank you.

The new glass shelf was slipped onto the Crisper drawer housing and fit perfectly. I was concerned that the dimensions were not exactly right (too small) but the replacement part fit perfectly.

The Condenser Fan Motor was already removed due to searching for the problem. The new fan motor looked different from the original but I felt very comfortable that Part Select had sent me the new part showing original part number changing numbers over the years. Simply placed the fan blades onto the new motor lined up 2 of the holes placed screws and tightened then plugged the wire ribbon into the Condensor Fan Motor, plugged in the Refridgerator and it worked beautifully.

The instruction video on the Part Select Web Site made it so incredibly easy to install. Installation took under 3 minutes!

Checked Video online. Had to remove the 2 snap on track/gear covers. Pry out the gear with screwdriver and the gear bearing unit. Align the flat side of the bearing unit and snap in. Position the cut teeth on the gear to match original and snap into the bearing. Insert the connecting rod into the long shaft gear and then push back into the short shaft gear. The video said to remove the drawer front but I did not and don't see that it necessary.

This problem is caused by a "Duckbill" rubber grommet attached to the bottom drain tube of the freezer. This duckbill opens up during the defrost cycle and allows water to drain down the "water slide" to the evaporator pan. It doesn't take much to gum the Duckbill. Once gummed up the defrost water is trapped. The Defrost Cycle eventually makes the water flow out of the coil area to the bottom of the freezer then eventually to the floor. The repair involves unplugging the unit, removing the bottom back cover with a 1/4 nut driver, pop the power clip out to give you room, reach in and pull the duckbill grommet and the water slide, then installing this replacement drain kit. This is a p trap replacement that actually fixes the root cause of this problem. A tricky part is removing the water slide, you can see the white snap that holds the slide in place. Using a small flat blade from the top releases the snap and the unit is pulled upward rather easily. This replacement drain clip snaps in the same place. If I had to do this again it wouldn't take more than two minutes to replace. Oh, one major thing, you need to manually defrost the unit. I pulled the front door off, it is held with 4 screws ... don't remove them just loosen them and it pops off easily. I pulled the bottom tray out an it gave me room to squirt hot water with a baster into the back freezer area. Eventually everything thawed out. If I had it to do over I would have waited on connecting the tube to the evaporator pan and placed the bottom of the tube into a small sauce pan or something to collect the drain water and easily dump it into the sink. I used a sponge and that took forever. BTW, just to reiterate, use this item and not that Duck Bill for replacement, this actually fixes the root cause of this problem!

I noticed the coils very dusty dirty, tried brushing it clean, ended up blowing it clean. I noticed the condenser fan motor was never turning, I had power, so I ordered a new one. I actual received the evaporator motor, so I had to order the correct one. After changing it, and it started blowing right away. But my refrigerator is still warm. I do not know where the evaporator blower motor is located. I cannot make out from the diagram breakdown. HELP

Pried out the old switch and installed the new switch.

Repair was tremendously easy. All I did was remove old light switch by prying out with screw driver and plugging in the new light switch and pushing it into the hole. Simple! The instructions weren't needed, but they were very thorough.

Watched a couple of videos. Removed left side hinge first, then did the same to the right side hinge. Part was installed in reverse order. Installation took less than 60 seconds.

Had to push the light switch to get lamp to light up.
Removed power from refrig. and removed old light switch
and replaced with the one I got from Partselect. Turned power back on and was done.

I popped out the old switch with a screwdriver pressing down the tab on the bottom and unplugged the terminals. Then I plugged in the new switch and popped back into the socket. Piece of cake!

The best part of the repair was how easy it was to find and order the part. Instead of searching the parts houses around town I just went to the PartSelect web site, quickly found and ordered the part in about five minutes, received the part the next day at my home and was ready to make the repair. Wow! What a pleasure for something to work the way it was meant to. Removed old switch located by prying out with sharp knife or screwdriver. Don't worry about breaking it or cracking plastic. Disconnect(unplug) wires from back of switch. Replace (plug-in) wires on back of new switch. Insert in location of old switch. Finisheed.

Shut off water supply. filter is located in the upper right hand corner of the refrigerator on the inside. open the drop-down door. by hand pull the filter downward. then twist it to the left one quarter turn. it should pull out. I replaced it with a filter bypass plug. you can purchase a high quality filter to replace.it don't buy cheap filter.I made that mistake! hope this helps good luck!

installed new parts

replaced electric control board, defrost for six hours. next day (24 hours) same problem, dusterhoff2928@charter.net