CTF17CFG Hotpoint Refrigerator - Instructions

Connected the 2 wires and pushed in the switch until it clicked.

First of all, I was very surprised and pleased that I could even locate the replacement part for such a refrigerator I've had for years. The two crisper pan covers arrived the next day (couldn't believe the fast delivery). I proceeded to take the broken crisper covers off and replace them with the two new ones, which fit perfectly. I then slid the crispers into the slots so they could slide in and out. It took me less than five minutes to do. No tools required.

1) This is a built-in refrigerator with the compressor, coils, etc. at the top. Turn off the breaker to the fridge. 2) Remove the front panel off the top (just push up and pull out). 3) Removed 2 screws to the old timer and carefully remove the plug. Plug the new timer in and screw in. 4) Since our fridge was heavily frosted up, we moved everything to another refrigerator and coolers and kept the refrigerator off until all panels were room temperature. 5) If you haven't cleaned the coil in a while, vacuum it with a soft brush attachment. 6) Turned back on and the refrigerator is cooler than ever!

Emptied freezes, turned off power, took floor of freezer out [4 screws ], took two screws out of fan mounts and replaces fan. Reassembled by reverse process. Simple

Noticed the fan was not working properly and went online and found out that was the cause. I immediately ordered the part that night at 8:21pm and received the motor and fan blade the next day. I flipped the refrigerator on its side and removed the 3 hex bolts, took off the fan blade first and removed the wires from the motor. I put in the new motor and then added on the new blade and put the 3 hex bolts back on and the wires. The whole process took about 30 minutes. Piece of cake.

per your instructions

Checked the defroster coil which is located behind the rear panel in the freezer compartment, it was still working. Followed the schematics down to the defrost timer, which is located in the lower front of the refrigerator and tried that. Plugged in the new part and the problem is solved.

I simply removed the broken drawer and replaced (inserted) the new one.

Naturally you have to push the frig from the wall and unplug it form the wall outlet and while you are removing and installing the old motor and installing the new motor. Do not open any of the frig and freezer door untill you are finished and you plug the power cord back into the wall outlet. Remove the lower back panel with a screw driver or a 5/16th hex driver. It is a kind of carboard. Once all the screws are out of that panel pull the top out from behind the steel above and then pull it out from the bottom and set it aside. Unplug the power line off of the motor. There are 3 separate brakets holding the motor in place. 1st remove the fan from the motor by romving the finger nut off the motor shaft and then remove the 1st bracket screw from the bracket all the way. Then use a light to see the other 2 screws and you will see that you do not have to take them all the way out like the first one. Just loosen the other 2 and then turn the motor and brackets counter clockwise and then pull the motor and brackets all out as one from the right hand side of where the brackets were mounted. I took the motor and brackets to the counter and removed te brackets from the motor and installed them to the new motor making sure that the bracket with the one screw hole in it is mounted at the right place so that when you reenstall the motor and brackets will let the motor wire connector be the closest to the outside where you can replug the power cord back onto the motor. Install the fan onto the new motor with the new finger nut that comes with the new motor. replace the back panel and pkug in the power cord fot the frig and let it run. Mine ran a lot quieter after the new motor was plugged in. Have fun if you have to do it. It is worth it.

I had wasted 5-6 weeks waiting for SEARS to send me the CORRECT Part. They kept sending the wrong part, telling me that the right one would be sent "THE NEXT WEEK" & Then finding out that the CORRECT ONE was on BACK ORDER with NO KNOWN DATE of shipment in Sight! So I looked up the part on the Internet. FOUND PartSelect & THEY found the CORRECT PART(That was on Saturday) with in 3 days... I had the PART! PLUS the Part arrived in GREAT SHAPE-NOT SO WITH SEARS which came with the packaging ALL TORE UP & THE GASKET was half out of the box and BADLY RUMPLED UP! PARTSELECT had very helpful instructions on their site & Over the Phone helped me do it in little or no time at all! I did remove the 2 screws at the bottom or the door-VERY EASY!!! atwhich time I saw that I also needed 2 nylon washers(I had several on hand!) Removing the whole door is not necessary, but in my case I FOUND the very worn washers & Was able to replace them too!... Now the door moves alot easier! PLUS: with the door off, I could do(replace the metal strips)on the Bottom & Inside gasket EASIER!... I WILL NEVER get partsfrom Sears again & ALL of my future Parts Purchases will be from PARTSELECT! I am VERY IMPRESSED & HIGHLY RECOMMEND PARTSELECT!

I followed the instructions verbatim as others explained. I did it step by step exactly as instructed, The timing was almost exact no more than 30 minutes. I removed the fan the night before the delivery of the new fan and used a small desk fan to cool the compressor. It worked fine in one half hour my freezer read a perfect zero. Thanks for all the help