CSK24GRXAAD Hotpoint Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- C. Robert from Sandusky, OH
- Parts Used:
- WR2X4901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Door closer cam riser
I blocked the door up with one 2X4 Then removed the lower hinge, installed the closing cam. Then I found that I needed one more closing cam that I didn't order the first time. This other one mounts to the lower section of the door and both cams set together. Re-ordered another cam. When it came in I installed it. Between ordering both parts I had them both in three days. The best to Parts Select
I now know where to buy my parts if needed again.
Thanks
Bob
Sandusky, Ohio
I now know where to buy my parts if needed again.
Thanks
Bob
Sandusky, Ohio
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carl from SAN MARCOS, TX
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Ice Maker Leaking
Researched on internet/you tube; ordered part, and did the repair. Easy to do and saved the cost of a service call.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from Louisville, KY
- Parts Used:
- WR2X4901
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Door had sagged, wouldn't close well.
At first, I noticed the refrigerator door didn't close at the same level of the freezer door. I started to adjust the hinges and noticed a chewed up black 'washer' at the base of the door hinge. Ppartselect.com was awesome, in that I easily found the schematic of my fridge, and the part I needed. Ordering was a snap, and it came to the house pretty quickly.
Installation, first raise the door up as high as you can, then scotch it with wood blocks (closed door). This takes the pressure off the bottom hinge you must remove.
Taking the hinge off is a snap, but then the problem presented itself. The old door closing cam was riveted to the hinge. I couldn’t get the old one off! I ended up taking it to the garage and breaking out the Dremmel tool with the abrasive cutter (the one that will cut through nails. I ended up cutting off the rivet. This was a pain.
I then found a small nut/bolt and put the new piece on, then put it back into place and removed the blocks. Works good as new. The toughest part by far was getting the old cam off… but there may be some easier way to get the rivet out that I’m not aware of.
Good luck.
Installation, first raise the door up as high as you can, then scotch it with wood blocks (closed door). This takes the pressure off the bottom hinge you must remove.
Taking the hinge off is a snap, but then the problem presented itself. The old door closing cam was riveted to the hinge. I couldn’t get the old one off! I ended up taking it to the garage and breaking out the Dremmel tool with the abrasive cutter (the one that will cut through nails. I ended up cutting off the rivet. This was a pain.
I then found a small nut/bolt and put the new piece on, then put it back into place and removed the blocks. Works good as new. The toughest part by far was getting the old cam off… but there may be some easier way to get the rivet out that I’m not aware of.
Good luck.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Philip from S BURLINGTON, VT
- Parts Used:
- WR17X11653
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Remove front cover
Remove front cover did not remove wires remove ice and water unit took off flapper put new one on 5 minutes back together
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from Rogers, AR
- Parts Used:
- WR17X11653
- Difficulty Level:
- Difficult
- Total Repair Time:
- 30 - 60 mins
Watched video on flapper assembly replacement looked real ready. Video failed to mention ice dispenser trim was glued in place . Had to buy real small paint scrapper that would fit in dispenser outlet to free inside edge of trim piece. Once I got it all loose job went very easy.
Use small putty knife to cut internal sealant on ice maker door trim piece. Then you can easily remove it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- J Stephen from BETHESDA, MD
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Warm air enters ice dispenser on door
Replaced flapper. Followed the video. The lamp caused the removable plastic bracket (which supports the control panel and the ice chute) to fuse with the plastic frame in the door. Eventually broke the fused plastic, removed the bracket, and filed the rough broken plastic before reassembly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from Virginia Beach, VA
- Parts Used:
- WR2X4901
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Socket set
Refirigerator door would not close all the way on its own.
The repair went well could have completed the job in 20 minutes if I had a selection of small nuts and bolts to replace the rivet that had to be drilled out. Also buy 2 of the door closing cams Part # PS297995 one goes on the bottom hinge of the refrigerator door the other on the bottom of the refrigerator.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wayne from Concord, NC
- Parts Used:
- WR2X4901
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Bottom cam at bottom of door broken.
Read the how to's AFTER ordering the part. 2 things....1) I wish I had read the comments first and 2) it was much easier than the comments led me to believe.
Had I read the comments first, I would have known to order BOTH the upper and lower cam....though there not a problem with the operation of the door. It would just have been a tad better if I had both. I'm not wanting to have to pay shipping for an additional part when the door works satisfactorily as it is.
As to the comments on how to do it....I took none of them. I (instead) removed the top hinge, and lifted to door off. I did have to have assistance to get the hole in the door aligned with the post, but that was rather easily done.
Would I do it again.....in a heart beat. I feel that I've save on the repair man making a call at the house, and experience has had me charged $60-$100 for virtually the same amount of service. My cost...shipping and all was under $20.00
Had I read the comments first, I would have known to order BOTH the upper and lower cam....though there not a problem with the operation of the door. It would just have been a tad better if I had both. I'm not wanting to have to pay shipping for an additional part when the door works satisfactorily as it is.
As to the comments on how to do it....I took none of them. I (instead) removed the top hinge, and lifted to door off. I did have to have assistance to get the hole in the door aligned with the post, but that was rather easily done.
Would I do it again.....in a heart beat. I feel that I've save on the repair man making a call at the house, and experience has had me charged $60-$100 for virtually the same amount of service. My cost...shipping and all was under $20.00
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- charles from moundville, AL
- Parts Used:
- WR2X4901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Door wouldn't close tight.
I placed books under the door until I had enough to hold the door up about 1/2 inch higher then when it is closed. The books and the magnetic gasket will hold the door, JUST DON'T TRY TO OPEN IT TILL YOU'RE THROUGH. That's about how high the cams lift the door when opened. I removed the two screws holding the door stop. Then removed the two screws holding the lower hinge pin.
It takes two of the cams
and the bottom one is riveted to the hinge. I used a grinder to grind the rivet so I could tap the pin out holding the cam. Put the new cam on and put the pin back in. I didn't put a new rivet, just gravity should hold it. I put the second cam on the hinge pin and one of the screws on the door stop holds it in place after you slide the hinge pin back into the door and replace the screws in the bracket then the door stop.
Make sure your lower door gasket didn't get damaged while the cams weren't working because the door wasn't being lifted up when opened.
It takes two of the cams
and the bottom one is riveted to the hinge. I used a grinder to grind the rivet so I could tap the pin out holding the cam. Put the new cam on and put the pin back in. I didn't put a new rivet, just gravity should hold it. I put the second cam on the hinge pin and one of the screws on the door stop holds it in place after you slide the hinge pin back into the door and replace the screws in the bracket then the door stop.
Make sure your lower door gasket didn't get damaged while the cams weren't working because the door wasn't being lifted up when opened.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GLen from Greenfield Twp, PA
- Parts Used:
- WR2X4901
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Socket set
broken door cam will not close on its own
First i removed the lower cover below doors . Then placed a 4x4 under the door to be fixed to keep it in place. Removed screws from hinge support on unit to remove cam Removed outside screw on door and loosened other to allow other cam to be removed . Always buy two cams if one is broken the other cant be in very good shape .The door will work like new with two .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alex from Cary, NC
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Frost buildup in freezer by the ice maker
Replaced dispenser door flapper by following the do it yourself video in this site. It was really easy. Just be careful when removing the dispenser black bezel. I broke one of the little tabs when taking it off.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rudy from CITRUS SPGS, FL
- Parts Used:
- WR17X11653
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Had a drip which filled up the tray and leaked on the floor from water dispenser
There are Great videos on YouTube!!! Turned off power,Removed trim ring, Pushed a philips head screwdriver in one of the holes underneath the electrical panel with the selector push buttons. This releases the electrical panel. There are Three wire sets with plugs. I removed the plugs and took the electrical panel out. Removed four Phillips head screws and pulled out the big paddle switch. This then exposes the flapper. Replaced flapper with new one and reassembled everything. When I had everything apart, I cleaned with window cleaner. It was pretty moldy from the water leaking. Turned power back on and tested everything to make sure I didn't mess anything up. Works great
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from BRICK, NJ
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
My ice container and Ice chute were freezing up and getting blocked, and my filtered water line was also freezing
I just followed the instructions on the video and it was exactly as they said......no surprises.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George V. from PITTSBURGH, PA
- Parts Used:
- WR17X3489
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Freezer Light Shield Cracked at mid fastening point
replaced the broken one with the new part
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Salinas, CA
- Parts Used:
- WR2X4901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Socket set
Door closing cam split in two and door would not automatically close anymore.
This one is a no brainer… One Phillips screw on top to pull top door hinge trim. Two nuts and the top hinge is free. Then pull the door… it helps if you unload all the crap in the door bins. Remove the remnants of the door cam and that leaves a pop rivet. Put some vise grips on the head and use a hacksaw to remove the lower part of the rivet. Then pop-rivet the new door cam in place. If you don’t own a pop-rivet tool, I guess you could use a 10/32” screw and nylock. Plop the door back on and you’re done. Took all of about 15 minutes.
Was this instruction helpful to you?
Thank you for voting!