HSK29MGWHCCC Hotpoint Refrigerator - Instructions

The replacement frame arrive fast and as ordered. Used the two rollers from the broken bin frame to install on the new frame. Also the glass shelf does not come included, so transfer that from the old bin frame.Total time of replacement was less than 5 minutes.

Looked it up on You Tube and basically followed the very simple instructions. Two minor differences: 1) I took the old gasket off while the door was still attached to the fridge. And 2) because it was a side-by-side freezer/ fresh food, I didn't have to take off the freezer door at all and the fresh food door was only attached at the top with 2 screws covered by a hinge cap. So I undid the screws and lifted it off the lower pin. We put the door on a table handle down and slightly off the table edge. Inserting the v-shaped rubber part of the gasket into the groove was easy- pinching it together with my fingers with a little hammer tap at the corners. Reinstalled the door and voila. 27 minutes!
Most of my DIY projects take twice as long as expected. Much time is spent taking off the old part then not as easy as expected to replace the new part. This was a breeze!

found the correct bulbs, the hardest part.
un screwed old bulb.
Screwed in new bulb.
Waa La,
There was light.

I took the ice drawer out and turned it upside down. Then removed two philips screws holding the drawer front on. Then with a small straight edge screwdriver pry out the sides to release the locking tabs and remove the auger and crusher assembly. Then on the end of the auger remove the e-clip, slide the auger out and remove the broken part of the crusher dispenser and replace with new. Easier than it sounds. Parts Select was great to deal with. Had my parts in two days.

Very easy novice could do

just had to unscrew old one put the new one in

I went to the internet and found parts select web site. Saw all of the possible fixes for my problem and read all of the other repair stories. My story actually became a journey that is still continuing. I first changed the water filter, but still no water at the dispenser. I next disconnected the coupling at the bottom of the freezer door that carries water to the dispenser and when the dispenser was depressed, water flowed at the coupling, but not at the dispenser. After reconnecting the coupling, I turned the freezer setting to 1 for 4-5 days, but still no water at the dispenser (possibly the line was frozen, but we had recently been away for a week and the water dispenser still supplied water at a freezer setting of 4). Now I am at the point of the journey into replacing parts one at a time to get water. First I ordered the dual water valve for the ice maker and water dispenser. I replaced this valve with instructions from Parts Select and still no water at dispenser. Next I ordered and replaced the switch at the dispenser lever and still no water. Next was the solenoid attached to the ice door, ordered, replaced and still no water at dispenser. I am now at the final part in this repair and that is the $132 circuit board. So I will be ordering this part soon and hopefully that will fix the issue.

1. Emptied the crisper pan,
2. Removed it from the refrigerator,
3. Flipped it upside down,
4. Removed the old one by pulling it off,
5. Replaced it with the new OEM part. and
6. Reversed the process.

Nothing to tell it was just a replacement part that the old part was removed and the new one inserted. Works like a dream Thanks

Removed ice bucket and emptied it, storing ice cubes temporarily in another container; Removed broken support and replaced with new. Removed rotor/crusher assembly from ice bucket assembly, replaced broken rotor (other vendor), reassembled ice bucket, filled with stored cubes and reinstalled in freezer.

removed the ice, auger, bin assembly and slowly examined it and began disassembly until i found the broken part and then removed them .. i went online and found the parts almost instantly the parts came in 2 days , the repair video,s were most helpful so much so that i decided to replace the ice chute, door solenoid which looked difficult until i watched the repair video and read other peoples feed back well good luck ! DM

There are three holes under the front panel in which you push a very small screwdriver in and the front panel comes off.In back of the panel is another panel with 4 screws .1 at each corner.Remove the 4 screws and that will come off exposing the working parts that need to be replaced.This is also a good time to clean anything you can get to in that area.It is very important to remember how everything came out.

Removed icemaker from freezer, remove covers allowing access to dispenser. In the next step I removed the auger and broken shield as one assembly. With assembly out of icemaker it was a simple task of taking the broken shield off of auger and putting the new one on. Reassemble in reverse order as removed.

Removed broken switch with plastic scraper (press tension latch on bottom), moved two wire terminals to the new switch and pressed the new switch into the hole.

Opened package and just snapped in front insert. Took longer to open package than it took to replace broken insert.