CSXW27CLJ Hotpoint Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Kevin from Orange, CA
- Parts Used:
- WR72X209
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Drawer slide rail broken
Since I ordered the right part thanks to the website, installing was easy. I just put the part in place and screwed the two screws into place. It took less than 2 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joel from Melville, NY
- Parts Used:
- WR72X209
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Slide rail cracked and fruit drawer wouldn't slide open
Trust me when I say that I am not a very handy person. It took only a matter of seconds to remove the broken slide rail, took 2 screws out. I found the part easily on the website, placed the order and the part was in my house in 2 days. My 12 year old son and I replaced the slide rail in a matter of seconds-required only the same 2 screws to secure in place. We replaced the glass shelf, slid the draw into place and now it is as good as new! A very easy repair!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from Spartanburg, SC
- Parts Used:
- WR72X209
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broken slide rail
Remove the 2 mounting screws, remove broken rail, install new rail and install 2 screws. I was finished in about 2 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from North Haledon, NJ
- Parts Used:
- WR72X209
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broken rail
removed broken rail and replaced two screws and the job was complete...took longer to clean the botom of the refrigerator than replace the part
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carmine from Millington, NJ
- Parts Used:
- WR17X2740
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
Replaced corroded auger
Removed front cover, removed rear cover careful to note position of spring assisted parts, used pliers to unscrew auger rod end cap, removed and soaked in Lime Away fixed and movable blades. Reassembled using diagram on website for guidance.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roscoe G from ROCHESTER, NY
- Parts Used:
- 40A15
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Light burnt out.
Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Natalie from Randallstown, MD
- Parts Used:
- WR17X2740
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
the auger was rusty, causing ice to have brown spots
Pay close attention to how you disassemble everything. You might even want to take a picture. I taped all the screws right where I unscrewed them, to make sure they were replaced in the right section. Also use the picture diagram that on the computer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john from milford, CT
- Parts Used:
- WR30X256
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broken ice bucket
Very easy to repair-Went online-Found diagrahm-Ordered part-and presto it was fixed.
Very good schematic to go by. If you can read you most likely can fix it.
Very good schematic to go by. If you can read you most likely can fix it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Azle, TX
- Parts Used:
- WR17X2740
- Difficulty Level:
- Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
The auger was rusted with age and made the ice taste bad.
The disassembly and reassembly was straightforward but the parts diagram was very helpful to help you get it back together. Make sure you get the convexity of the clip that retains the clear plastic barrel to the auger pointing in the right direction. The metal plate that that comes out with the assembly seems to rust as fast as the auger, so you should just order that when you order the auger. I did not replace the plate so I cleaned it and painted it with epoxy paint before I reassembled.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jimmy from saluda, SC
- Parts Used:
- WR17X2740
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
would not dispence ice
remove ice bucket and replace broken augar
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paula from Boca Raton, FL
- Parts Used:
- WR72X209
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
slides were broken and draws cracked
Emptied the old draws and removed the old sliders. Took time to screw the new ones in. The draws are not as nice as the original ones.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Corpus Christi, TX
- Parts Used:
- WR49X10183
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Rust in ice
Replaced auger and front helix kit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from Paducah, KY
- Parts Used:
- WR30X256
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Collar that holds Ice auger assemble was Broken.Seems to be a manifacturing defect in this model.
I simply ordered a new Ice bucket, removed about 6 Phillips head screws, removed the old bucket from the Ice door and replaced with a new bucket. SIMPLE !!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Laura from Colorado Springs, CO
- Parts Used:
- WR71X1936
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Missing a shelf in freezer
I saved about $15.00 by ordering the part on line. It came in about a week and was a super easy process. Since it was just missing there really wasn't anything that needed fixing. just installed it where it belonged and all was good. Great and easy experience.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- VERN from KEIZER, OR
- Parts Used:
- WR17X2132
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench set
Water resivour for drinking water developed crack
The replacement part came with a one page instruction sheet. Following those instructions I cut the two hoses on the old resivour and removed it. I then cut the hoses on the new resivour to desired length (all inside the refrigerator). Using the two couplers provided with the new resivour I hocked the two hoses together and tightened them with a wrench. It took longer to clean the refrigerator than it did to replace the part. Instruction sheet was very helpful
Was this instruction helpful to you?
Thank you for voting!