CST20KABAWH Hotpoint Refrigerator - Instructions

First i removed the lower cover below doors . Then placed a 4x4 under the door to be fixed to keep it in place. Removed screws from hinge support on unit to remove cam Removed outside screw on door and loosened other to allow other cam to be removed . Always buy two cams if one is broken the other cant be in very good shape .The door will work like new with two .

I aligned the back of the controller with the slot in the icebox and it popped right back on. No more frozen vegetables.

At first, I noticed the refrigerator door didn't close at the same level of the freezer door. I started to adjust the hinges and noticed a chewed up black 'washer' at the base of the door hinge. Ppartselect.com was awesome, in that I easily found the schematic of my fridge, and the part I needed. Ordering was a snap, and it came to the house pretty quickly.
Installation, first raise the door up as high as you can, then scotch it with wood blocks (closed door). This takes the pressure off the bottom hinge you must remove.
Taking the hinge off is a snap, but then the problem presented itself. The old door closing cam was riveted to the hinge. I couldn’t get the old one off! I ended up taking it to the garage and breaking out the Dremmel tool with the abrasive cutter (the one that will cut through nails. I ended up cutting off the rivet. This was a pain.
I then found a small nut/bolt and put the new piece on, then put it back into place and removed the blocks. Works good as new. The toughest part by far was getting the old cam off… but there may be some easier way to get the rivet out that I’m not aware of.
Good luck.

First I removed the drawers. Then I removed the 2 screws from each side. Then replaced the 2 pieces in the same manner using the same screws. It took about 15-20 min. Very easy. Drawers work perfectly now. Glad I found this site.

The repair went well could have completed the job in 20 minutes if I had a selection of small nuts and bolts to replace the rivet that had to be drilled out. Also buy 2 of the door closing cams Part # PS297995 one goes on the bottom hinge of the refrigerator door the other on the bottom of the refrigerator.

Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.

I placed books under the door until I had enough to hold the door up about 1/2 inch higher then when it is closed. The books and the magnetic gasket will hold the door, JUST DON'T TRY TO OPEN IT TILL YOU'RE THROUGH. That's about how high the cams lift the door when opened. I removed the two screws holding the door stop. Then removed the two screws holding the lower hinge pin.

It takes two of the cams

and the bottom one is riveted to the hinge. I used a grinder to grind the rivet so I could tap the pin out holding the cam. Put the new cam on and put the pin back in. I didn't put a new rivet, just gravity should hold it. I put the second cam on the hinge pin and one of the screws on the door stop holds it in place after you slide the hinge pin back into the door and replace the screws in the bracket then the door stop.
Make sure your lower door gasket didn't get damaged while the cams weren't working because the door wasn't being lifted up when opened.

First a big thank you to PartSelect.com. I read the stories posted by others before ordering the parts and found out that I probably needed 2 of these cams. So I followed the advice of others and ordered 2 cams. I'm really glad I did because once I got the door off I discovered both were broken up real bad. Maybe you guys should think about offering them as a set?
Anyway the repair was fairly easy, except for the bottom cam which was revited to the bottom bracket. Again, thanks to the other stories about repairs with this part I was already expecting this. So the repair went like this. I removed the door by unscrewing the hinge on top(1 screw and 2 bolts). Took the door off and laid it on its side. Removed the bottom bracket( 2 bolts). Used a drill to drill out the rivit. Used a spare screw/nut that I had in a tool box to fasten the cam to the bracket. Put it all back together and I was done. The biggest challenge was figuring our if I needed 2 cams,so with the advice of others on your site, my repair was a snap.

Removed four screws at bottom of door, while someone held the door in place replaced the upper cam (there are two) applied some silicone plumbers lube between the mating surfaces and tightened it up. Works like new bottom cam was only slightly worn. P.S. Remove everything from the door first.

I blocked the door up with one 2X4 Then removed the lower hinge, installed the closing cam. Then I found that I needed one more closing cam that I didn't order the first time. This other one mounts to the lower section of the door and both cams set together. Re-ordered another cam. When it came in I installed it. Between ordering both parts I had them both in three days. The best to Parts Select
I now know where to buy my parts if needed again.

Thanks
Bob
Sandusky, Ohio

Like the rest of the other statements it was easy with 2 2X4 pieces of wood to block the door up. The other suggestion about buying two of the pieces was a good idea. Once I took off both the top and bottom pieces they were both worn out and it was easy to replace them both at the same time. The door is working good again and shuts on its own.

This was a 15 year old great working GE regrigerator. Refrigerator was not cooling properly, though the freezer worked great. Using flashlight, examined cam riser which was clearly broken. YOU MUST ORDER TWO GASKETS AS BOTH WILL BE WORN. After removing all food from the door, taped plastic sheet over the open space to keep food somewhat cool Removed top hinge cover and screws on top of door and lifted door out of bottom bracket placing it flat on kitchen island. Unscrewed hinge elements including old broken cam and shims form the bottom of the door and fit in the new cam. Unfortunately one of the shims was broken, so I used a thin plastic black washer from the hardware store which was big enough to fit over the pin on the bottom of the refrigerator itself. Screwed all the parts back together. Be VERY careful to note how you removed them in the first place...mabe take a digital foto or two. This was kind of tricky to remember. Then used a hammer and chisel to break off the rivit holding the bottom hinge elements on the refrigerator. Sawing with jigsaw didn't work that well. The rivit came right off. Then used a flat head screw, lock washer and nut instead of a reivit and attached the new second cam riser. You are now done with the new parts. Simply reattached the door and it closed like new. Had a simultaneoius problem with a faulty defrost heater in the freezer which also had to be replaced and which was really easy to do. About an hour max. This was the real cause of the refrigerator not cooling properly. But that's another story.

took top bracket off--then removed door--took
bottom bracket off bottom of door and replaced
door closing cam and reasembled---a piece of
cake

Same problems as already described .... door would not close, plastic bits on floor, angry, ready to throw-out 15 year old “dog” and blow at least $1,000 on a new appliance!

This repair is dead easy. Remove the two bolts holding the top hinge and lift off the entire door. Don’t be surprised if the original Riser Cam has virtually disintegrated, mine was a wreck. Remove two bolts that retain the old flat metal “shim” and fiber “gasket”.

Fit new Riser Cam and re-use old shim and gasket. Replace door on dome-shape bottom hinge mount and then re-fit top hinge.

If in any doubt order new shim and gasket along with the new cam riser. Or, do as I did, and “manufacture” either of these parts from scrap material found in the workshop ....

After reading the stories here, I purchased one door closing cam. After getting into the problem area, I realized I needed 2 cam, so I put the door back together and ordered another cam. If you have this problem, buy 2 cams.