CTG21GABGRWW Hotpoint Refrigerator - Instructions

I took out the vegetable bins and slid in the part. Replaced vegetable bins. Works perfect. I was told locally that GE doesn't make the part any more and that I wouldn't be able to find one. First place I looked on the net was you and found it with no trouble at all. really thrilled to get it. Thanks

I used pliers to pull lightly on the head of the switch, while I inserted a small flat head screw driver into the base of switch and gently worked around the edges to free it from the panel.

After replacing the light bulb and still no light I manually pushed the light switch button. Intermittently the light would come on then go out. I removed the power plug from the power source then replaced the light switch. I plugged the refrigerator back in and now I open the door the light comes on and stays on until the door is closed.

The part arrived It said to warm it to take out wrinkles but not even a picture of how to take off the old or put on the new. Everything on the internet in general about gaskets explained about unscrewing the old gasket but I couldn't find any screws. The user feedback mentioned no tools and that was our only clue and the only reason we finally succeeded. We looked at it repeatedly over 5 days. Pulled and pushed and could not figure out how it was attached or how to unattach without breaking things. I finally got out a screw driver and tried to pry it off. An hour later I got a corner piece started to come off. We pulled all the way around and got it off easily once started. We again struggled to put the new one on. Couldn't really tell what area of the gasket fit back into the crease. It kept falling off. Finally we pushed the correct edge of the gasket into the crease. VERY difficult. Fat edge fits into skinny crease. Took a lot more strength than expected so it didn't seem right but it was. Took a while and a lot of strength to work the corners and sides in. Eventually got the whole thing on. A picture and 4 sentences would have been a big help. Wouldn't try it again. To anyone else...No screws. Use a lot of strength. I hope someone publishes a picture for you.

The old switch was hard to remove. Thinking that I may have to loosen the wires I used a socket wrench to remove a clamp. This was unnecessary. In the end the switch did come out using a large size screwdriver. The problem was that the expanding plastic tongue is not visible from the ouside so you have to try to feel your way around. If i had ordered the replacement before and not afterwards I would have seen this before hand.

I first unscrewed the broken right rail from the back piece and replaced with the new rail. Did the same for the left piece side. Attaching to the front rail was challenging because I took a while to figure out how to remove the cover (where the pictures of the vegetables/fruits are). But if you just get a narrow flat-head screwdriver under there, it just pries off. Then you can get to the little screw that attaches the side rails to the front piece.

I ordered two switches, replaced both with a knife in 10 minutes. Interior light works, thanks.

a simple matter of putting the new shelf back in place an reconnecting the shelving brackets. pretty self-explanatory.

I removed the Glass Shelf on top of the Vegetable Drawer assembly, unfastened the front rail from the broken slide rail and removed the entire assembly. I cleaned the parts and then installed the new rail. I placed the drawers in the repaired assembly and placed in the refridgerator. It really went well. I didn't need the other parts order. I only had them just in case they were needed.

Snapped end cap onto bar and installed bar onto freezer door.

I considered going to an appliance parts store but found the part very easily on the internet and had it within 2 days. I am very busy which was very helpful.

I found instructions on the web about how to do this repair, so I ordered the part with confidence. But the instructions simply said "pull out the old switchlight". That was actually somewhat difficult as the clip on the side intended to hold the part in was stubborn. I eventually used a utility to slice off the clip. From that point, it was just a matter of plugging in the new switchlight , which was very simple.

I removed the condenser cover removed old fan blade defrosted the condenser section installed new blade and reassembled

First i removed everything from the bottom shelf, removed the glass, then removed the entire bracket assembly. Then removed the front metal strip to expose the front mounting screw, then removed the rear screw. Installed the new part and reversed the procedure.

The replacement cap fit perfectly. Unfortunately when the orinigal cap broke it tookout a small piece of the surrounding plastic leaving nothing for the new cap to catch. I have the piece and tried several kinds of glue but nothing holds it securely enough. I would however readily recommend your company. The service was terrific.
Thank you.

I removed the brackets with the metal strip attached, from the door. I took a screwdriver and pressed down on the parts holding the strip to the brackets . I attached the new strip to the brackets and then attached the whole thing to the door.
Really easy to do.