CSF22TCM Hotpoint Refrigerator - Instructions

when I got on your site I was able to find the part easily & your installation video was a big help. It fit perfectly & was very easy to install--it's working great!!!!!thank you so much

I watched the you tube video. Very easy! the part was easy to order came earlier that expected and was fixed in less than 5 minutes!

Unscrew 2 screws to remove broken part, screw in new.

Ordered part on line, arrived the next day. Looked at the screw (phillips head). Had trouble dropping screws but got our magnetic phillips head and it worked like a charm. So proud of myself as my husband did not have to do a thing.

Best for 2 people on this repair as 1 person needs to hold the door and the other position the bottom pin in place on reassembly. On my side by side I was replacing the cam on the cold food side, not the freezer. But I got down and inspected both the broken cam and the cam on the side that wasn't broken to understand how the parts fit together. Each door has 2 cams that work/fit together. So be sure the one you are replacing is installed properly (flat side towards the door body). Remove all contents from inside door including the shelves. Use a phillips screwdriver to remove the cover plate on the top hinge. Use tape or a marker to mark on the refrigerator top a corner of where the bracket is positioned, for proper placement on reassembly. While someone is holding the door, remove the 2 bolts from the top bracket (or the back one is just loosened so bracket can be moved out of the way). Lift door off the bottom pin. Turn the door on its side to expose the bottom bracket. There should be 2 bolts here. The furthest one from the pin only needs to be loosened. The other bolt will need to be removed but as you do this be sure to not let the other 2 metal pieces fall out. Remove the broken cam and replace with the new part. Realign the parts and bracket over the pin rod hole and tighten both bolts. Replace the door onto the bottom pin. Then add top bracket and align it to the marking and screw back in these 2 bolts. Test door for any needed adjustments (I had none). Then replace the top bracket cover with its screw. Voila! Clean the shelves and put them in the door and fill them up. :-)

1. Watched the video on how to make the repair. 2. Used the tools recommended. 3. Followed easy instructions as demonstrated on video, and Viola! It was repaired.

I followed your terrific video. I first got all tools ready, covered a table in cardboard, and removed food from the fridge door. I removed the cap and screws on top of the door hinge. Lifting the door off was simple, and after laying the door on the table, the retaining screw was easily loosened, and the cam screw removed. The only problem was that half the thin gasket under the broken cam was missing. No new gasket came with the part. I wanted the new cam to lay flat, so I made a partial gasket from a matchbook cover and filled the gap. It all went back together quickly. Just have tools ready beforehand. Ten minute job, unless you have to make a new gasket or part of one. Thanks, guys.

Removed food from shelf, removed shelf, removed slide. installed new slide. Perfect fit

Real simple actually.... tracked down the model number. Found and ordered the needed part on partselect.... it arrived OVERNIGHT (scary!). Remove the pieces of the old bracket that were laying in the bottom of the fridge. Remove the 2 mounting screws... install the new slide rail with same screws. Re-install drawer. DONE.

I loosened to Philip's head screws and removed the broken glide, then replaced the new glide, lining up the holes, and then screwing in the two screws from the old glide. This solved the problem- a quick fix. Thank you!!!!

I ordered a door closing cam (4320595) to start with and then relized I needed Bottom Hinge Assembly which I ordered#4326874. I had no problem installing. I have returned for credit the door closing cam. I HAD NO TROUBLE INSTALLING THE BOTTOM HINGE ASSEMBLY. ONLY TOOK 10 OR 15 MINUTES. I am a retired building contactor and hade all the toos necessary.

Followed the instruction video. The price was high for a plastic part the size of a quarter.

This is the third time I have used parts select to fix an appliance. I have saved thousands now in replacement costs and certainly hundreds in repair costs. They had exactly what I needed and the online diagrams made it easy to identify the parts I needed and install them too.

Took out the broken one and replaced it with the new one.

I ordered a cam riser for the refrigerator door. I watched the "how to" video the day I ordered the part. It took about a week to get the part, but I was ready when it arrived. The 'how to' video was a big help. It showed me how to take off the door and replace the part. The process was quite simple! Oh! Don't forget to turn the refrigerator on again!