CSF22TCM Hotpoint Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Diane from Whitestone, NY
- Parts Used:
- WR72X207
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The drawer side rail was cracked and could no longer support the shelf and drawer.
I ordered the part on Friday afternoon and it was delivered on Saturday morning. I removed two screws took off the old piece and screwed in the new piece in about 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- nthony from Overland Park, KS
- Parts Used:
- WR72X207
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Drawer Slide Broke
Just replaced the drawer slide. The thing that amazed me was the speed I received the part, I ordered it on sunday night and it was delivered tuesday afternoon, great job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- vincent from mahwah, NJ
- Parts Used:
- WR2X4901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
door was not closing properly
Your vidio was Brilliant !!i just followed your instructions
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles M from Concord, NC
- Parts Used:
- WR2X4901
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Wrench (Adjustable)
Door Closing Cam broke
The bottom of the door was 5 " off the floor. A 2x4 block and a 4x4 block were pushed under the door and supported it while the water line was disconnected the hinge removed and the cam replaced. It was a simple fix and reading other people's experience made the repair so much easier.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from Upper Malboro, MD
- Parts Used:
- WR2X4901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Door would not shut by itself.
I followed the directions on the computer and everything went just as the video said it would. This was one of the easiest repairs I have ever done. Usually, it does not go as planned.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Neal from Cleburne, TX
- Parts Used:
- WR2X4901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Door would not close properly
Removed the door and loosened the bottom bracket and scraped the old cam off. Mounted new cam and tightned the bracket. Replaced door and it was a total sucess.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary Helen from San Antonio, TX
- Parts Used:
- WR72X207
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Plastic Rail Broke
Unscrewed broken rail and screwed in new rail. The best thing was how easy it was to identify the part I needed and the prompt delivery of the part once I ordered it. Thank you very much. I was very pleased with your service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barry from Ashland, VA
- Parts Used:
- WR72X207
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
the side rail which the vegitable drawer slides on and the top glass rests was broken form too much weight.
Repair was very simple. Removed the glass and drawer. Unscrewed the two screws holding the rail on. Put the new rail on with the same screws. Replace the glass and drawer. What was really cool was pluging the modle number into Google and your site was one of the top three. The brand name was different, but the refrigerator was identical. Must have been sold under more than one brand name.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bobby from Danville, VA
- Parts Used:
- WR2X4901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
door dropped down and draging, would not close
Buy ( 2 ) cams !!!! removed hinge cover and hinge on top of the door, ( 2 screws )...lift door off of the bottom hinge and lay door on the floor, remove broken cam on bottom of door with nut driver, ( 2 screws ) , install new cam..... remove the bottom hinge off of the front of the refrigerator with nut driver, (2 screws ).... saw rivit off and remove old cam, install new cam and secure with new bolt and nut,... reinstall hinge back on bottom front of refigerator.....replace door back onto the bottom hinge.....install top hinge back onto the top of the door....replace hinge cover......done !
Was this instruction helpful to you?
Thank you for voting!
broken slide rails
Removed two screws on each slide rail and used the same two screws to install new rails. The job took only a few minutes. The best part was the promptness of the delivery. I ordered the parts at 12P on Thurs and had them on my porch at 10A on Fri. Thanks Gary
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lynn from Naples, FL
- Parts Used:
- WR2X4901
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench set
Fridge door was not self-closing
Followed step-by-step instructions in previous post. Note that there are TWO approaches, both of which work.
Option 1) Order TWO cams (PS297995), drill out the rivet holding the frame's cam, and replace it with a nut and bolt. (See post on 07/19/09.)
Option 2) Order the entire hinge assembly (PS290199), which includes the door's cam and an assembled frame hinge and cam. (See post on 10/29/08.)
We opted for Option 1 which was pretty easy. Option 2 would be even easier and take less time but costs about $9 more.
Thanks to previous posters for excellent instructions!
Option 1) Order TWO cams (PS297995), drill out the rivet holding the frame's cam, and replace it with a nut and bolt. (See post on 07/19/09.)
Option 2) Order the entire hinge assembly (PS290199), which includes the door's cam and an assembled frame hinge and cam. (See post on 10/29/08.)
We opted for Option 1 which was pretty easy. Option 2 would be even easier and take less time but costs about $9 more.
Thanks to previous posters for excellent instructions!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- phyllis from owensville, MO
- Parts Used:
- WR2X4901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Old Cam Had Deteriorated, And Was Breaking Into Pieces And Falling Off.
We taped the door with 3 pieces of duct tape, then put boards under it. Used socket set to remove cam and then cut off rivet so we could just use a screw to keep in place. . . Just for your information, I ordered 2 cams, and was glad I did as I need 2 to make the repair. . . Didn't read about this online or on order recommendation. The cams go 1 up and 1 down thanks for the installation repair stories, it inspired us to "do it ourselves " and we saved about $75 to $100. 00
Was this instruction helpful to you?
Thank you for voting!
Slide Rail Drawers were broken
The ordering process thru PartSelect was simple. Model number got you to the drawings and from there it was " Click to the Cart". Delivery was as expected, but better than most companies. Replacement took only minutes. One thing to remember for future purchases is that hardware does not come along with the part. I had the exsisting screws so I was able to install quickly. I would definitely use PartSelect in the future.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from Tarrytown, NY
- Parts Used:
- WR2X4901
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Socket set
Door would not shut tight
Followed Partselect video on how to replace cam riser. Very, very helpful!
Was this instruction helpful to you?
Thank you for voting!