CSX22BCBEWH Hotpoint Refrigerator - Instructions

By the time this failure (failed defroster heating element) is evident (top of freezer starts thawing), the entire freezer coil is encased in a block of ice & frost is visble on the back freezer panel.
Empty the freezer & unplug (or turn circuit breaker off) then remove all racks and the light bulb then remove the two lower drawer guides using a phillips srewdriver (2 scrwes each). Use a 1/4" nutdriver to remove the two panel screws on either side of the light bulb socket and pull the panel out, unclip the green grounging wire and set panel aside. this exposes the freezer evaporator coil which is probably encased in ice. If so, use a heat gun or hair dryer to melt the ice away. This takes a half hour of heat application and a bowl or other catchpan should be placed under the coil to remove some of the resulting melting runoff so the evap. pan under the fridg/freezer unit won't be overwhelmed with the excess water.
Replacing the defrost heater & bracket assembly itself is just a matter of removing two phillips screws on either side of the bracket assembly, pulling the bracket free and then uncliping the two electrical terminals. Clip in the new unit to the eletrical terminals & replace the screws, reinstall the rear panel (don't forget to reconnect the ground wire), install the drawer backets, light bulb, shelves and drawer & reapply power. Replacing the bracket itself w/o the defrost proceedure takes about 15 minutes.

Note: If this symptom occurs and is diagnosed (the heater tube will be black and electrically read as "open" using an ohmmeter) and you cannot get the heater assembly & bracket assembly immediately, you can use the heat gun (hairdryer) manual defrost proceedure noted above to get the the unit running while you await the parts arrival. I used the manual defrost procedure and there was just some moderate frost on the coils after five days when I was able to install the replacement part.

Unplugged refrigerator and turned off water valve at wall. Removed the entire back, lower cardboard panel (turns out I didn't have to do this...could have just removed the screws from the right side and folded the cardboard along a perforated line designed for that purpose). Removed screw holding water control valve to back of refrigerator. Took new control valve, and slipped on adaptors for electrical connectors (in bag) to the two smaller of the four electrical prongs). Removed electrical sockets from old connector and placed them over appropriate prongs on new connector. Unscrewed the two old water out lines, cut the old fittings off and slipped the lines snugly into the new outlet valve (new valve had slip on connectors not requiring lines to be screwed in). Keep straight which line goes to which outlet port! Then removed water line going into old fitting and screwed it on to new valve inlet fitting (after removing black plastic protective cap). Turned wall water valve on, checked for leaks (none), and plugged refrigerator back in. Water restored to both icemaker and water dispenser!

By the way, the first valve came damaged, but one phone call and the people at Part Select promptly sent out a replacement which I had the very next day (and this was two days before Christmas!). Great job!

This is such an easy fix!
1-Unplugging the fridge and emptyi it. Remove all shelves.
2-remove the 2 screws at the top of the back panel with a 1/4 inch nutdriver. You'll have to tilt ithis panel forward and sideways to get it out.
3- DO NOT CHIP AT THR ICE COVERING THE COOLING COILS? Replace one shelf and rest a hair dryer on low heat on the shelf.. Plug the drain hole at the bottom with a rag so all the melted ice water doesn't flood the floor under the fridge. Soak up the water with a rag and bucket- this should take 20-30 minutes.
4-Remove the red and blue power cables from the element. Only 2 philips head screws hold the defrosting element in place. Once it's out you can tell it's burned out because it looks black like a burned out lightbulb.
4-Plug in the red and blue power cables to the new unit. You will need to reroute the blue power cable because the new unit has both power connections on the same end.
5-Replace the cover panel by sliding it in at an angle and replace the 1/4 inch screws.
6-Replace the shelves and plug in the fridge.
That's it!

The only difficult part was not knowing which parts had to be removed to gain access to the flapper to replace it. It appeared as if the frame around the control panel would have to be removed as well as the door handle; we tried but were not able to remove the frame. It turned out that the panel just popped out with the frame in place. Once we had access to the flapper, it was easy to replace it. The repair fixed the problem.

The most difficult part of the repair was the melting of the ice and preparation. I did change a single element heater for a dual element heater, which required a little manual flexing of the sub-frame, but it assembled with little issue. I was lucky, I did not have to splice the extended harness connection. Rerouting my existing gave sufficent length.
Not sure if the single elements were changed for dual, but it did have the same PN as the unit I replaced.

After reading posts on this website, I determined I needed to replace the defrost heater. Removed heater to take a closer look and after testing with a voltmeter determined it needed replacing. Ordered part online and could not believe how quickly it arrived. Blue wire that travels down the left side of the freezer coils had some damage on the end of the plastic connector so was pleased to find that I was able to splice the extension wire provided in the defrost heater kit onto the blue wire and dispose of the damaged end. It's been about 10 days and I do believe my problem has been solved!

Emptied refrigerator door shelves. Supported door with 4x4 blocks. Removed old door hinge and replaced with new door hinge and cams. Pleased with end result and dealing with PartSelect.

I unloaded the door and took the cover off at the top of the upper hinge (1 phillips screw) I then unbolted the upper hinge (2-28mm bolts) and lifted the door off. I was surprised how light it was. I laid the door down and installed the new cam riser on the door. I then unbolted the lower hinge (2-28mm bolts)and installed the new hinge.
I lubed the 2 hinges with vaseline and put the door back on the lower hinge. I then reinstalled the upper hinge and cover. It took about 15 minutes, and a lot of that was cleaning up. Oh yes, to get at the lower hinge you have to pull off the lower grate that covers the coils. It just snaps off and on. It was a very easy job.

At first the part appeared to be too large because of the change from one heater to two heaters in the replacement part. It was necessary to push a copper refrigerant line back out ot the way about an inch or so before the part would fit properly. This might take a little courage from the do-it-yourselfer, but it moved easily and seems no worse for the move. Currently the fridge is working well(two weeks) with no buildup of any frost on freezer panel as previouly noted. Overall experience was just fine. Makes d-i-y guy look good!

I Took the six screws off the back panel to get to underneath the refridgerator. took the 2 screws out of the bracket thast holds on the water valve took the 2 lines off and then put everything back

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires.Threw away the old defroster. Put the new one in. I had to reroute the blue wire over to the right hand side and plugged it in.Put the back on. put the shelves in and I was done! We had this done just about 3 years ago and it cost us about $175. The cost of this repair was only $38.05 with shipping and all! What a great deal! Thanks so much PartSelect!

My husband took out the old icemaker in about 5 minutes. The new icemaker was a perfect fit even though the refrigerator was >10yrs old. The only difficult part was the plug extension that was needed so that it would fit into an older appliance. The part was included, it just made the cord about 3 inches longer than it needed to. After working with it for about 20 minutes we were able to fit it on the back side of the icemaker. Now it works great!!

I cleaned out the door and removed the top hinge. Lifted the door and layed it on the floor. Removed bottom hinge from refridgerator installed new hinge. Replaced plastic stop on door. Used broke hinge to align it and tighten. Lifted door onto new hinge and installed top hinge. Instead of buying $35 dollar hinge buy 2 plastic stops. You'll have to drill out a rivet on bottom hinge but it will save over $30.00.

Removed shelves and storage drawer from freezer.

Removed the two screws that mount the rear panel cover at the back of the freezer
compartment. Disconnected the grounding clip on the cover exposing the evaporator coils and the defrosting heater at the bottom.

Removed the remaining ice chunks on the coils.

Removed the two screws mounting the single element defroster. Disconnected the wires on each end of the defroster.

The replacement defroster was a two element heater and the instructions clearly showed how to re-route the single wire from the left side to the right side. The harness kit included a short piece of wire and a crimp connector to ensure the length would be sufficient to connect the new heater.

The only item missing in the kit was the RTV required to water proof the wire connection. A quick run to the hardware store took care of that.

Reassembled in reverse order, plugged the refrigerator back in and by the next day temperatures were normal in both the freezer and refrigerator compartment.

A service repairman had quoted $60.00 for the defrost heater plus $250.00 for installation. Using parts from PartSelect the total cost was $44.00 including shipping and about 30 minutes of my time. I'll take the savings anyday.

Thanks for the easy to read instructions and multiple status email notes of the order.

I followed the easy instructions included with the replacement part I ordered. I removed the back of the freezer, unpluged the broken heater and replace with the new heater. The heater just plugged in, very very simple. I put the back panel bach on with the two screws and it perfectly. Not back for a girl!