HTG22CBMARWW Hotpoint Refrigerator - Instructions

replace sensor in refriger.

The problem began when freezer thawed and could not keep food frozen. Initially, I thought the issue was the defrost heater (because I had seen similar symptoms previously and resolved the issue with a new defrost heater)and I replaced that part with a spare that I had puchased previously. The issue was still unresolved and I noticed the evaporator fan was not running in the freezer because it would not turn on when I closed the door. I checked to make sure I could hear the compressor working (and it was)and concluded that the evaporator fan motor was not running. I ordered the part and found a YouTube DIY video on how to replace it. While I was at work, my fiancee took it upon herself to watch the installation video and install the new evaporator fan motor and all is well.

I watched the videos before I received my parts. I thawed the freezer out, removed the panel in the back. Cut the wires to the defrost thermostat and spliced the new one on with wire nuts and tape. Then I did the same for the temp. sensor. Put it all back together. Now the freezer isn't running all the time. I set the temperatures back to normal and it seams to be fine.

Removed the panel on the back wall inside the freezer side. To do this I unplugged the appliance, removed the racks, drawer, bulb and two screws holding the panel in place. The defrost cycle was not working so ice buildup on the coil was to the point of blocking air flow to the refrigerator side. I used a hair dryer set on high and stuffed two towels at the base of the coil to collect the melting frost and ice. Once the coil was clear of frost and ice I took the defrost timer off by sliding the clip off the tube, cut the wires and stripped the ends so I could use wire nuts to make the new connections . Placed the new defrost timer in the clip and reattached in the same location the old one was removed from. The sensor was replaced by doing the same steps. I replaced the panel after all the wire nuts were secured and the wires were tucked away where they would not interfere with the fan. Replaced the bulb, drawer, racks and food and plugged The refrigerator back in. 20 minutes from beginning to end.

I was intimidated by this repair(as I am with most repairs), because there were 2 possible problems. But being able to purchase both parts for $30 (including shipping) made it worth a try. Thanks to the instructional videos that were sent, the repair was much easier than I anticipated. For me, the hardest part was fitting my shoulders in the narrow freezer. Now the appliance works like a charm. This would have been a $150-$200 repair had I called a company to do it.

I replace defroste thermostat :i defrost al the ice

Removed the back pannel from inside the freezer. Defrosted the ice build up. Removed the shroud from the back top of the freezer. ( This contains the fan and the light assembly). Removed the fan and replaced the motor. Cut the wire for the temperature sensor and wired in the new one. removed the defrost thermostat and replaced with the new one. Reassembled the unit and reinstalled it into the freezer compartment. replaced the pannel and plugged unit back in.

changed sensors did not repair problem,replaced damper with mechanical damper fixed problem.

After removing all the parts, the bins and a large glass fitted shelf or lid, on top of the two crisper bins I then removed the whole frame the three glides are mounted to. The frame is molded into one large piece matching the whole horizontal space of the refrigerator, so it is wiggled loose from its space. I lifted out the whole thing and placed it on a surface on which I could work while see everything I was doing. With no screw (both top and bottom of the U-shaped gripper “clevis” end are solid) or other type fastener that could be removed I finally just pried the "clevis" of the center glide that grips the front of the frame. This clevis grips a set of small plastic studs that fit into matching round indentations in the top and bottom of the clevis jaws. It’s necessary to keep the stud from slipping back into the first indentation while opening up the other side of the jaw so that both are free at the same time and the clevis will slide sideways. Using a butter knife because it was a good fit and stiff enough, I released the top, and then the bottom using the knife to bend it a little bit. The clevis opens up just enough to allow the edge of the frame it’s gripping to be released from its grip. The new one is put back in exactly the same manner but in reverse. The opposite end from the clevis simply tilts up until it can be disengage and reengaged in the same manner

I followed the video instructions online and the job went very smoothly. Unfortunately, the problem is still occuring [this of couse is no fault of yours] there must be another problem to remedy. Really appreciate the videoThanks Parts Select for excellent product and quick delivery

The replacement went very well. The video was not just as the unit I have but with a little work I worked it out. The service was very good. I received the part in 1 Day. Thanks for the good info. Keep up the good work regarding the videos. This helped. Just for the info. I did a post mortem of the switch. The strain of the wires pulling on the switch caused the failure of the switch. The design of the old temp switch was bad and workmanship was very poor in the original box. Thanks again Ron

I followed instructions posted by experts and hands-on experienced owners on PARTS SELECT.Very helpful! Repairs was easy!.Defrost thermostat tried first,unsuccessfull then the DEFROST HEATER HARNESS next :BINGO !. Thank you PARTS SELECT ! Thank You every ones who posted their successful experiences that gave me confidence.From now on I know I can count on PARTS SELECT and its sites to solve my future headaches!

Replaced top sensor in ref. and top sensor in freezer as well as defrost thermostat - works as advertised - easy fix, saved a bundle thanks to this site! Parts ordered and shipped quickly and without complications!

My son replaced both temperature sensors and the fridge works great now!!! Like brand new again!!!!

I watched the video then ordered the defrost timer it was here in two days (ordered late saturday arrived tuesday). Spent $. 16 On two wire nuts and went to work . The repair took one hour including defrosting the coils with a hair dryer . Your website is my " go too " for parts and repair. I spent less than $20 including shipping !