CSZ22DRAAD Hotpoint Refrigerator - Instructions

I stacked three 2x4's that were approximately as wide as the door in length. This required lifting the door about 1/4" but it also got the weight of the door off the cam so the bracket assembly that the cam was attached to could be removed. I drilled out the rivet that held the old cam in place and like previous DIY's had to use a small bolt and nut to secure the new cam in place. Reattached the bracket with the new cam and that was it. The only problem was that the head of the bolt I used was not flat enough to allow proper clearance for the door to swing freely without feeling some drag and the wife noticed that immediately. I told her to wait until the weekend and I would again remove the door and file down the head of the bolt to allow the required clearance. After a few days of use, the door itself ground enough material off the head of the bolt so that the door began to open and close properly. So now she's happy, I'm happy and the dog is happy.

took out 4 screws - lowered timer cover - replaced timer- put it back together

Door cam disintegrated after 20 years. This was a terrific site for suggested repairs. My problem was not paying attention to how the door shim, cam and spacer were placed on the hinge. Most of the site's instructions did not forewarn the obvious...pay attention when doing repairs!!

Instructions from others were generally pretty good but as adept as I am at D-I-Y I still did not pay attention to how I took something apart so it could be assembled properly.

I don't think that ordering an entire door hinge set is necessary. It does not appear that shims and/or spacer come with the hinge assembly. Door cam was all that was needed. I thought about replacing the cam on the freezer side but won't do it until absolutely necessary.

This is a very good website and my thanks to all of the posts for the instructions!!

I removed the shield over the timer and the part that supported the timer. Just unpluged it and pluged in new timer and put back shield. I had already replaced the defrost heaters which had totally burned up. I also replaced the thermostat while I was making the repairs although the old one was still o.k. All the information that I needed to make the repairs I obtained through your website. After looking at several websites to compare prices-etc, I found yours to be the best overall. Thanks-a-million your website is worth it's weight in Cold Food !

disconnect the power to the unit. remove the retainer sctrews on the mounting bracket. remove fan motor from unit. using the rerquired tools remove the fan from the old motor and install on the new one. torque the nut until all slack is out then 1/4 turn. reinstall motor assy. and reconnect power. test the system .

We took the drawers out unsrewed the slide rails, screwed the new ones back on and replaced the drawers. the door cam was alittle harder because we had to lift the door to put it in but it still took under 10 min. altogether it took about 25 minutes. I am also planning on buying a few more parts from the company so I will end up paying about $50 to fix a fridge that I got for free. WHAT A GREAT DEAL!!!!!

From instructions found on the site I was directed to the defrost timer part being bad. And from the information others posted that have had the same problem I was able to replace that part by removing the bottom grill just below the door and on the left side was the part. Removing one screw to remove the bracket from the frame and then another screw to remove the part from the bracket. I found it easier to remove the part from the bracket before I pulled the part out so I would have more room to unplug the connector. Just reverse the steps to replace the new part. It took about a day or so for the refrigerator to get to the proper temp.

Removed the ice maker from the freezer. Removed the switch. Tested the switch with a multimeter. Ordered a new switch. Replaced it in the box. Installed the ice maker ( 3screws and electric cord plug. It works. Details available on the internet.

This part (plastic tubing) does not show up under my model of refrig...so I had to look thru the various water lines and pick the one that "looked" right. Luckily, this is the exact replacement part and works perfectly. I removed the lower back panel from the fridge, removed the bracket holding the water line connectors and pressed the outer ring of the coupler up until it released the old water line. I pushed in the new line, made sure it was snug with a gentle pull and ran the line under the fridge up to the existing coupler. I removed the old line from the existing coupler under the front left of the freezer door, and pushed in the new line. I did not need to use the new coupler. If my old line would not have been so brittle and cracked in several places, I could have just cut out the leaking portion and popped the new couple in to mend the line back together. Easy job and we can stop buying bottled water at the store now!

Unplugged frige, removed top shelf, pulled broken fan blade off. Replaced with fan blade just purchased from PartSelect. Very simple repair. Orderd and recieved the right part.

At first it appeared all was lost since the sales and sevice facility said parts for our GE refrigerator were no longer avalible. We were looking at a $1200 dollar purchase. We decided however to research the internet and see if parts could be obtained. We found Parts Select and to our suprise parts were readily available. We order the drawer side rails and received them within days. The repairs were completed in minutes and for less the twenty bucks.
Steven

Was able to pull the door up to the normal position, then blocked in place with 2 2x4's. Easily removed the hinge assemble and the door closing cam, which had broken in two.
bolted on the replacement parts in 10 mionutes and the door was a good as new: peice of cake!!!

First I turned off the water supply. Then I removed the ice bin and the ice maker by removing 4 screws and 3 electrical connections. This allowed access to the evaporator fan which was not moving. To remove the evap fan I removed two screws that hold the fan bracket. The fan assembly now had to be pushed back and rotated to remove from hole. There are 3 electrical connections that have to be disconnected from the fan, one ground wire that also is connected to the fan bracket and 2 power connections. Installing the new fan was the reverse of the above except the power connections were in a different location and i had to use the extension wires provided with the new fan to have the length needed to make the connection.

removed old parts and installed new. went smooth

I took the advice off of your website about the only thing that will fix
the problem is change the run capacitor. I felt assured that I would
have a working refrigerator freezer after making this change. I was
pretty disheartened when it didn`t solve anything. I was not going to
take the new part back out after the small challenge of putting it in.
The next day I found out how to test the old capacitor and it was still
good. I will just have to eat the $49. I did learn not to take advice from
a website even if it seems like a sure thing