CTX21GAXARWW Hotpoint Refrigerator - Instructions

I took the drawer and shelf out,unscrewed the old slide, then screwed the ne wone in. Put the shelf back in and then slid the drawere right in!

I removed the gasket starting in one of the corners, until the gasket was completely removed.
I then replaced the gasket with a new one by starting in one of the corners and pressing it on to the track around the door.

Just as your video described, although due to the age of the fridge, it took a bit longer to remove the defective switch. Your video made this so simple, I can't imagine why we lived with a dark fridge for so long! I was ready to buy a whole new fridge, as repairmen are often nonexistent for small repairs. I am the biggest fan of your company & it's repair video. THANK YOU SO MUCH

I took all of the creases out of the new gasket with hot water as described on the delivery box. I laid the gasket on the floor and let it cool while I took the refrigerator door off, laid it on a table, and removed the old gasket. I started the new gasket into the groove at one corner and pressed it into place by sliding my thumb along the gasket and seating it as I went. It was an extremely simple task which took about 2 minutes. The most time is consumed in removing and replacing the door

First i removed the vegetable drawers and slide rails. Removed two screws from the old rail then replaced it with the new one. Then replaced the vegetable drawers. It was that simple. The replaceement part was delivered to my home in threre days after i ordered it on line. It was better than going to a dealer and having them order one for me then having to make another trip to pick it up.

The repair was very simple. The longest part was taking everything off the shelf in the refrigerator so that the slide rail could be removed. Then when things were out, it was clear that the bottom of the refrigerator needed cleaning. The repair itself was done quickly. The cleaning (yuck) took longer! this is a great site because the part came quickly and it was very easy to select just what was needed.

The entire frame that holds the two crisper drawers pulls right out. After that, it's just a matter of unscrewing the broken part, snapping in and screwing the new part and sliding the whole thing back in.

Remove bottom glass shelf, lift up -then remove entire drawer slide assembly.Remove plastic decorative front cover(it just snaps off) and unscrew left side drawer slide screws.replace with new part and screw in screws. Replace in bottom of fridge and replace glass shelf.So Easy that an average house wife like myself was able to do it alone.Almost as easy as finding the part needed on partselect.com! Thanks, it was much easier than apple pie.

Removed two screws, lined up the rail and replaced the screws. That was it!! Glass shelf sat on top and bin slid in smoothly.

Pulled out old drain gromet. Have to be careful not to put drain in motor. Experienced repair person could probably to in 5 minutes; it took my husband about 15 minutes. Did not really need entire drain line; just connection at top.

Using plyers Pulled old switch down and out. Put new one in and pushed new switch up into position. The switch plugs into the contacts, no wiring needed. Worked like a charm. You saved me 200 dollars GE repair bill. Thanks

Your online helpful hints made it easy as pie.

Removed rer cover, unplugged starter assembly from side of compressor and replaced unit with a new one. Plugged fridge in and it works good.

The hardest part was figuring out the part needed from so many little pictures. The actual repair, a piece of cake!

I replaced the thermostat, temperature sensor, and the run capacitor. . . Refrigerator still not cooling. I checked the start relay and measured the input terminals on the compressor for the correct resistance. . . Everything measured correctly. In a last ditch effort before calling for service, I pulled the main board, inspected it and saw the problem right away. One leg on the compression capacitor had desoldered itself. Got out my soldering iron and applied a good amount of solder to that point. Put everything back together and turn it on. . . Problem fixed. The compressor kicked on right away and started cooling the refrigerator.