CTX21BAXARWH Hotpoint Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Colby from Blanding, UT
- Parts Used:
- WR55X24064
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Starter/overload assembly and run capacitor were bad
Removed rer cover, unplugged starter assembly from side of compressor and replaced unit with a new one. Plugged fridge in and it works good.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eleanor from Elko, NV
- Parts Used:
- WR17X2769
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Broken side rail to vegetable bin
Took the old frame apart - two screws - replaced broken side rail and put frame back in frig. replaced glass shelf and bins. Frig good as new. 15 minutes. Pretty good for and 81 year old lady.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Bel Air, MD
- Parts Used:
- WR55X24064
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Refrigerator and freezer drawer would not maintain set temperature
Condenser fan motor was running slow. This was not a problem included in your list of possible problems. I thought that maybe the capacitor was bad but have no way to check it. So I ordered one. when I received it, I installed it. That was not the problem. So I ordered a fan motor and installed it. That was not the problem. So finally I ordered a control board and installed it. That solved the problem. So maybe you should put "cond.fan motor runs slow" in your list of possible faults and what causes that problem. Capacitor was easy to install, simply remove the cover plate, flip off retaining wire, unplug the capacitor and replace. Fan motor was a bit more difficult. It must be removed from mount after fan scroll is removed. Remove one screw that holds scroll, bend the top down and remove. Then pull hard on fan blade to remove it. It must be installed on new motor. Two screws in frame mount can be removed with some effort if you have a 1/4" drive ratchet with a Phillips screwdriver bit. Then pull frame open and install new motor. Push fan blade on new motor shaft hard. Replacing control board was easy. I used a pair of long nose pliers with 90 degree bend to get mounting pins closed to pull board off.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Andres from Macungie, PA
- Parts Used:
- WR24X446
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench set
gasket cracking at least 8 years old
Excellent instructions from your video. Replaced gasket once without removing door quite harder to do. Placed gasket in sun to warm it up, didn't have to heat it in hot water. Much easier once doors are removed and replaced gasket on large table or bench. Thanks for the video and your prompt delivery of part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kent from Summerville, SC
- Parts Used:
- WR24X446
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Fresh door gasket leaking.
Followed the PartsSelect how-to video to the letter., using clothes dryer option to soften the gasket before installation. Installing the new gasket a little tedious, but not difficult. Video was dead on as to method and tools.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- theodore from salisbury, NC
- Parts Used:
- WR60X30349, WR60X114
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
bad fan motor
take fan out,put new in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from NORTH PALM BEACH, FL
- Parts Used:
- WR24X445
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
Freezer door gasket replaced
Both PartSelect and GE advisors told me to remove/loosen screws holding gasket to the door. This model has no screws. After pulling to old gasket from a corner (very difficult) I found that it is held in place by pressing it into a channel running around the door. Very difficult to line up the proper parts and very difficult to slide/adjust it into place. When finally installed, one corner of the gasket protruded so that the door was not flush and actually kept the door from closing. I tried to push/pull it into place. No good. Finally I tried to hammer the gasket back to make it flush. No good, as it evidently crushed the magnets providing the necessary holding power and produced gaps. I finally had to get foam window stripping plus heavy duty magnets to pull door to frame. Result: door closes OK but some moisture collects around door.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Simpsonville, SC
- Parts Used:
- WR23X37285
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
light switch quit working
removed the inside fridge electrical panel and swapped switches
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ANTHONY from NEW EGYPT, NJ
- Parts Used:
- WR23X37285
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
sticky switch
easy pry out, disconnect wiring, connect on new switch and press in switch.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Beverly from St Louis, MO
- Parts Used:
- WR17X2770
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
drawr slide broke
followed instructions from video on your site
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Durham, CA
- Parts Used:
- WR55X24064
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
compressor running and hot, refer and fridge room temp.
Watched a youtube on capacitors- though on a motor with a pulley, the symptoms were the same, motor running and pulley not turning-bad capacitor. Took a chance for a 17+ dollar part vs a new compressor. It worked.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOSE from NEW YORK, NY
- Parts Used:
- WR55X24064
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
fan and compressor wont start
Googled the model number of refrigerator with symptoms of "refrigerator wont run". Parts select web site appeared on my screen, opened Parts Select website, Partselect said probable cause of my frige symptom was that the run capacitor usually burns out 51% of the time. They were correct with the diagnosis 100%. I ordered the run capacitor for $23.00, installed it in 10 minutes, refrigerator runs good as new. Thank you for saving me cost of service call. I probably saved $200 or more. I will use Partselect again with my next problem. THANK YOU,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Keven from Fleming Island, FL
- Parts Used:
- WR17X2769
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
right side slide rail broken
pull the front cover off, take the two screws out and the side rail comes right off, put the new one in place, put the screws back in and bang!.....all done. Took longer to take the stuff out of the fridge than to make this repair.
Was this instruction helpful to you?
Thank you for voting!
left side rail broke in half middle support broke at front end
As instructed actually my wife ordered the parts and
Installed herself. Positive experience.
Installed herself. Positive experience.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jules from Crowley, LA
- Parts Used:
- WR23X37285
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
failed light switch
I started removing the switch by prying on the right side with a screwdriver, when it emerged enough I used pliers to finish removing it. I then unpluged rhe wires from the bad switch and pluged them on the new switch and "poped" it into the hole.
Was this instruction helpful to you?
Thank you for voting!