GRT15C2AW0 Gibson Refrigerator - Instructions

snapped shelf end cap in place, now my wine bottles don't fall on the floor when you open the fridge door!

This was not technical at all. The old door fell out and the replacement door snapped right into position. It was simple.

I tested the components in the refrigerator defrost function. I used digital multimeter and checked for continuity. Defrost thermostat must 32 degrees or lower.

Use the rubber brushing to fill the gap.

I simply removed 4 screws holding the casing and then 2 more holding the timer. It was very easy. I then replaced the timer by unplugging and plugged the new one in. I replaced all the screws and the job was done. Less than 30 minutes. I was very impressed with the shipping time. When I ordered the part, I had it the next day.

Unplugged fridge. Removed freezer shelves and unscrewed and removed plastic shelf brackets. Removed the lower rear panel. Removed the bin for ice. Removed the 2 exposed upper rear panel screws. At this point I was able to flex the panel quite enough to access the fan motor. Carefully plugged the fridge back in and turned it on long enough to verify the existing evap. fan motor was not running. Powered off and unplugged again. Removed the fan and it's support assembly, and replaced with new. Had to cut the wires and splice and crimp with the provided wire nuts since the plugs in this model were different. Powered on fridge to check fan function. Reassemble and go home looking' like a hero! Saved my BFF a couple hundred bucks.

I had to loosen the screw holding the mounting block and increase the hole size to fit the screw on refrigerator

The evaporator coil is behind the freezer. Remove the rack that makes the shelf and remove two 1/4” hex head screws I the back of the freezer to access the coil.
I used a hair dryer to melt the ice off the coil.
The thermostat clips on the refrigeration pipe to the coil. Remove the old thermostat and cut the wires at least a few inches from the thermostat. Clip the new thermostat on the pipe and strip about a 1/4” of the wire ends. The electrical connectors (provided with the new part) must be crimped to connect the wires.

I slid off old caps, then slid on new caps. I pushed down metal holding clamps and I was finished. The whole process was about 5 minutes. The parts select web site was great. I looked up my parts on the easy to use catalog and ordered them. Make sure you save the broken parts or write down the part numbers to make finding your exact parts easier. I wish all parts web sites were as easy to use as parts select.

Traced issue to defrost timer ( burned compressor & element contacts). This unit is mounted next to the temperature adjustment control in the refridgerator area - right in front. Removal of plastic cover provided easy access to the timer. Unit unscrews from the mounting then unplugs. Installation is reverse of removal.

Ordered the right parts thanks to your list of part numbers and where they were located on the refrigerator. They fit perfect and problem fixed in five minutes. This is the best site I have ever used!

Please keep up the good service you provide.

It simply snapped into place. No tools required. A very simple repair.

Ordered a new defroster timer and replace old one. It works just fine. A $35 repair vs a $500 new appliance.
Cool.
GWE

The switch prevented the door from closing about 5 years ago. So I just taped the switch down, and lived without a fridge light for the last 5 years. Painful! And wasteful (food spoiled because we couldn't see it.) Thought I was out of luck, assuming light switches were all the same, got fed up again, and pulled out old switch,,and searched the net for the part number, and just started calling the manufacturer. I got this website after no luck in calling, and took the step to order...and in no time, got it replaced, and we cam see now! It feels like we got a new fridge!

I had to cut the retainer bar to length and then snap the end caps onto the bar. Then just snap the assembly onto the freezer. No problem!