TBX22ZPDRAD General Electric Refrigerator - Instructions

It just unpluged and the new one plugged in. Simple. The part was reasonable and arrived very quickly. It sure is nice to have a light in the frig again.

Turned off the breaker to the fridge because I couldn't reach the power plug to unplug it . Use small flat head screwdriver to pop out the piece, disconnected the rubber prong connectors, inserted the new piece into the rubber prongs snapped it back into place. Flipped the breaker back on and prayed it worked. It did and I saved myself $120 service call.

My husband thought he would have to set aside time on the weekend to replace the gasket. It was delivered and I unpacked it put it on and that was that.

i pulled the old gasket off, and placed the new one in place, starting at the corners. then i lined up the insert in the gasket with the gap where it is to go and ran my fingers along the gasket, pressing in with my thumb.

I watched the video online, followed the instructions and within minutes had the part installed. The frig light was working once again! I will say the original switch was very snug and I had to do some very minor scraping of the plastic to get the new part to slide in.

Removed old gasket and installed new gasket, per the video instructions on the PartSelect website. Instructions were clear and accurate. I wondered if the new seal would fit snuggly and securely, but no problems. The seal holds the door closed more firmly than the old seal did. So far, so good!

Removed freezer door then refrigerator door. Layed it on a big drop cloth to work on it. Replace feeezer door and cover refrigerator opening with plastic or something to help keep the cold in.
Removing old gasket was easy. Just pull it out. Align the new gasket with metal bracket that holds it then firmly hammer it into place. You’ll know when it’s attached correctly cause it hugs the door properly.

Part was perfect fit .Removed fan .three screws.replaced that s it

Water was leaking from under the GE dishwasher, but once we pulled it out, had apparently been going on for a little while. Turning the water off to the dishwasher made it stop, so it was happening even when the unit was not running, potentially indicating somewhere early in the path of the water to and into the machine.

Indeed, inspecting the water inlet vale showed a slow leak. Getting the replacement part was fine, and it fit the electrical, water inlet (existing 90-degree water inlet elbow), and water outlet connections just fine - but the original machine screws that held on the original water inlet valve did not work. It took a little research to figure out the new type of screw required, which was apparently a 10/16 Type AB, which seemed to be a less common type of sheet metal screw (with a point), as opposed to the original flat-ended machine screws. So, after ordering those separately (which were a bit expensive), it went together fine.

A note on the water inlet valve part just indicating the the threading on those parts has changed over time, so potentially ordering the screws to attach it might be worthwhile, would be good information to add about the water inlet valve.

I watched videos of the modern refrigerators and figured out how to do my model by taking my time watching as many videos that pertain to my refrigerator I finally I expose the evaporator I noticed that the defrost heater was buckled up and totally disintegrated and slowly took my time looking at the screws I took it out and I didn't have to do
disassemble bottom of the freezer to replace the part, you definitely had to have common sense and to be mechanically inclined to do this repair otherwise it was easy

Allow 24 hours for new gasket to flatten out from packaging. Gently peel off existing gasket. Clean dirt and mold from mount area.
Mount gasket beginning at a corner. Press gasket into place every inch around perimeter. Done! Water is no longer in bottom of refrigerator and it is running more efficiently (less time running) due to the fact that it can maintain the temperature for longer periods of time.

1- youtubed the potential diagnoses, 2- resourced and ordered parts, 3- removed old socket, installed new one :-)... My fridge is an older fridge and could've used a screwdriver for eyeglasses. Plug and play easy... YAY!

Took old gasket off put new on.

Gasket came well packaged so only ran hot water over it briefly and put it on.

Placed new gasket into dryer,( recommended by 2 u tubes) high heat for about 10 minutes and was a snap getting softened gasket into little tiny slot actual placement was done twice as there was a twist in the seal i missed the first time so did do twice but was so easy this way was almost sad thinking it would have been 100$ deductible having someone do it and who knows what normal cost would have been......thanks u tube

This was so easy I think it took me 2 minutes. I am not very mechanically inclined but that didn't matter! Works perfect thank you!