ZISS36NCASS General Electric Refrigerator - Instructions

Unplugged unit. Closed water valve at wall. Removed back cover. Disconnected wiring. Removed valve body and cut hoses one at a time placed them in the new part. Re- connected wiring and attached part and backing. Turned water back on and plugged in chord.

It was as easy as the instructions were clear (and they were). Remove 2 screws and two nuts, pop out the old ice maker, pop in the new, plug in and tighten screws/bolts. It worked. I'm happy.

I removed the lower screw (not needed for the new icemaker), loosened the 2 top screws, unplugged the wire harness and removed the old icemaker. Unpacked the new icemaker assembly from the box, wiped the ice cube depressions to remove any debris, snapped on the water tube adapter, hung the new assembly on the 2 loosened upper screws and tightened the screws. The wire harness required the supplied pigtail plug which made the wire assembly long and awkward to replace the ice bucket/dispenser assembly, plugged it in and was done. It took a total of about 10 minutes for the entire operation and had a full bin of ice cubes within 36 hours and was ready for the ice dispenser/crusher in the freezer door. Easy install!

i did every thing according to instructionwhich was simple but it did not cover how to use the extension electrical plug-in and where to put the extra cord so the tray would go back in

The parts were here the next day. After removing the old ice maker it was a simple installation using the adapter cord furnished. It took about 15 minutes. You have to work with the cord some to get it to fit behind the ice maker, but it does fit. The ice maker started up immediately & works great.

A friend had no problem getting the new ice maker in. But then the problems started. The ice maker works great. But when the water fills the ice maker it squirts water onto the side of the freezer and ice sickles form. So we watched and decided the hole was too large so used a piece of plastic. That helped to cover the hole. But some water is still entering the freezer and not all going to the ice maker. The only other thing we can think to try is to use epoxy to try to close that place. A simple job has turned into a big headache. I wish they made the ice maker like the original one.

I ordered the replacement from you guys, got the new ice maker and the plug had an adapter, but it wouldnt fit in with everything. So I cut the plug off my old ice maker and put it on the new one and it works just fine.
thanks for everthing P.S. i got the ice maker from you for 109.00 and sears wanted 130.00 for it
good stuff good deal.

Used the nutdriver to loosen two screws, life out ice maker, disconnect electric plug and put aside. Placed the new icemaker on the loosened screws, plugged in electric connector and tightened screws. Used small level to verify that unit was level.Waited about two hours for first cubes to be released into tray - has been working fine since!

Replaced hose that cracked from over heating with new hose and couplers. This refrigerator will over heat easily and has been a real pain because of it. Must keep it clean and vacuum dust by removing back cover.

I first pulled the electrical plug. Then shut off the water supply, I unscrewed the screws holding the cardboard backing on the refrigerator, this exposed the water valve. The plug in water lines came out easily and inserted easily into the new valve. Turned the water on to check for leaks, none. I then plugged in the unit and after a few cycles I had ice. $53 dollars and some change and we are back in business. Thanks to you guys, it went smooth and the parts came quickly.

Removed the Ice maker from the freezer because the light was not on. Disassembled ice maker, found printed circuit board had shorted across two posts because the board was black in that area. Bought new ice maker assembly, installed in less than five minutes, making Ice fine.

My husband took the old icemaker out before the new one came in. When the new one arrived, I installed it in less than 10 minutes.

It took longer to remove the ice bucket and frozen food than it did to replace the ice maker. Remove one screw with a 1/4" nut driver, slide outward and remove plug. transfer water tube to new unit. plug it in, slide into rear slots and install one screw. Replace ice bucket and frozen food, shut the door and hear ice falling in about 30 min. Easy job! Great product! THANKS MJS

I removed the cover off the back and removed the screw that holds the bracket to the water Valve.
Pulled the element out and cut the water lines and placed them in each soleniod and then removed the 4 wire harness and placed then on the new water valve and , turned on the water and checked for leaks. Put water valve bracket back in place and checked for leaks. Everything was working properly. Replaced the back cover. End of project.

Removed old ice maker and control valve. Control valve is in the back of the refrigerator in the bottom corner. Unplug the refridge, turn off water supply valve, remove mounting screw and unplug the control valve from the wiring harness connection. Using a flat screw driver, remove the four water lines (this is the most difficult part). Go inside the freezer and remove the ice maker by loosening the two top screws and removing the bottom screw. Unplug the electrical connection by pulling straight out or use a flat screw driver to pry off. Installation of the new parts is the reverse of the removal. The new ice maker has a pig tail that is necessary to use. This pig tail is longer than the original but will loop up behind the unit and back down to the female plug. Full ice bucket in 48 hours.