TBX22PRYGRAA General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Ray from Fredericksburg, VA
- Parts Used:
- WR17X11653
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Air leaking into freezer through door dispenser
I followed the video instructions. They were clear and consise. I removed the trim ring and controls. Them removed the housing and flapper. I did notice a small burr in the plastic chute and foam insulation. I trimmed this off with a utility in hopes this burr caused the flapper to warp. This is the 2nd time the flapper has been replaced in 1.5 yrs. The repair was really easy thanks to the video.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jack from Ft Myers, FL
- Parts Used:
- WR17X11653
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
air leak from ice maker flap permitting frost buildup inside ice maker dispenser
Watched à video provided at your website. Removed te cover then removed 4 screws holding the control panel' snapped out the old flap and inserted the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wanda from Katy, TX
- Parts Used:
- WR17X11653
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The rubber seal on the flapper came off.
My husband made the replaced the flapper while watching the video provided in your email, it was easy. Thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rebecca from Banning, CA
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
ice dispenser frosting up
Watched the video from your site and followed instructions, extremely easy after that.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- steven from westminster, MD
- Parts Used:
- WR17X11653
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Door ice dispenser flapper warped/frost build up
I followed the repair video Partselect provided online. It the repair easy and fast. Great video!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jon from social circle, GA
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
frost formed because the ice damper let warm air into the freezer
Removed frame, unscrewed the electrical panel, and popped the flapper off. Installed new flapper. Replaced the electrical panel and re-installed the frame.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DON from ZELLWOOD, FL
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Ice Shute Flapper Was Distorted And Did Not Seal Opening Causing Frost Build Up
Removed control panel by inserting small screwdriver in the 3 holes underneath to loosen. Remove 4 screws holding circuit board . Unplugged 3 connectors. Removing circuit board gave access to flapper. Removed flapper by unclipping. Installed new flapper and reversed disassembly procedure. This was 2nd time in 2 years I had to replace this part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from Charlotte, NC
- Parts Used:
- WR17X11653
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Misting inside freezer which blocked the ice dispenser.
I followed the video instructions to the letter and it was very easy and a total success. I believe I would have had problems but for thr video demonstration which was very clear and straight forward in a simple manner. Thanks for the prompt delivery of the part and the help installing it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Sahuarita, AZ
- Parts Used:
- WR17X2770
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broken slide rail
Your online helpful hints made it easy as pie.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Raleigh, NC
- Parts Used:
- WR17X11653
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Ice accumulation inside the ice dispenser.
I watched the Utube video, repeated the process at home while awaiting the part, and installed the flapper door in about 15 minutes after it arrived--piece of cake. The hardest part was removing the escutcheon plate on the front of the freezer door. I figured out I could slide a putty knife under it and the rest of the project was completed in no time at all.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Fripp island, SC
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
3rd Flap for this Ice Mkaer, keeps warping
Very Easy, follow direction I the video.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Dumfries, VA
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Flapper valve allowing frost/ice to accumulate in chute in summer
Followed the online video exactly and it was easily done. Couldn't have been better. The problem is solved.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Luis from Chester Springs, PA
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Flapper was warpped
Follow instruction on the video you provided
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Beverly from St Louis, MO
- Parts Used:
- WR17X2770
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
drawr slide broke
followed instructions from video on your site
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gregory from Hughesville, MD
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
ice dispenser chute kept freezing with condensation
The flapper on the ice chute was curled up and not creating a good seat, so the chute kept clogging up with frozen condensation, especially during the humid summer months. The online video made it so easy to replace the part myself. I was able to fix the problem in under 15 minutes and at a fraction of the price!
Was this instruction helpful to you?
Thank you for voting!