TBX22PRYGRAA General Electric Refrigerator - Instructions

Replaced dispenser flapper

First, I had to remove the face plate where the ice and water was dispensed remove 4 screws holding the electrical circuits, disconnect circuits ,remove 2 screws holding soleniod and one screw holdin crank assembly. repace parts and screws.

First i removed the vegetable drawers and slide rails. Removed two screws from the old rail then replaced it with the new one. Then replaced the vegetable drawers. It was that simple. The replaceement part was delivered to my home in threre days after i ordered it on line. It was better than going to a dealer and having them order one for me then having to make another trip to pick it up.

1. Unplug the fridge
2. Removed the outer facing of the dispenser outside the freezer door. This is fairly easy, better with a tool (plastic scraper) that won't mar the finish.
3. Removed the plastic plate with labels -- water, ice, etc. This is done by sliding a small jewelers screwdriver into the slots on the left, middle and right in back of the plate. These are difficult to see without a flashlight.
4. Removed the four screws in the panel behind this plate.
5. Unpluged the large cable on the left side after the panel is freed.
5. Removed the rubber "dispenser" button. this just pulls off.
6. Remove the panel
7. Lift flapper up and remove. Clips hold this in.
8. Put new flapper in place.
9. Use reverse order to put back together.
Piece of cake. Ice maker no longer frosts up.!!!!

The repair was very simple. The longest part was taking everything off the shelf in the refrigerator so that the slide rail could be removed. Then when things were out, it was clear that the bottom of the refrigerator needed cleaning. The repair itself was done quickly. The cleaning (yuck) took longer! this is a great site because the part came quickly and it was very easy to select just what was needed.

Followed the instructions and replaced the door recess.

took off the panel, took out 4 screwws, took out old flap, installed new flap, put screws back in , and put trim back on.

This was very easy. Just unscrew the broken side pieces and attach the new ones. If the rubber gaskets are still in good shape, gently pull them off and attach them to the new rails. I was very impressed with the service from Partselect.com. I gave them my appliance model number and they helped me find the right part. I ordered on Sunday evening and had the parts in hand by Tuesday. Great service! I will definitely use this company if I need more parts.

I took out all the stuff on the shelf, and the drawers.
then I took out the shelf, pulled off the cover so I could get at the screws.
I unscrewed 2 screws, threw out the old part, and screwed the new one into the shelf.
then I put the whole thing back together, in total the hardest part was cleaning off the shelves and then putting everything back in.
As a note, there was a gasket on the old rail that was not on this one. I had some silicone tabs that I used instead, but I really think the gasket should have been part of the order.

Removed the broken rail (2 screws), replaced the new rail (2 screws), reassembled all in about 8 minutes. It was AWESOME!!! I had spent hours trying to repair it and, fortunately, gave up and decided to look online for the part. Didn't even think that the part would still be available. Not only was it available but it arrived in 2 days! Anything that is broken in the future: I am going to your website first! Thank you!!!

Pulled the outter cover off, removed the electronic board, replaced the flapper and put it back together again.

The entire frame that holds the two crisper drawers pulls right out. After that, it's just a matter of unscrewing the broken part, snapping in and screwing the new part and sliding the whole thing back in.

Remove bottom glass shelf, lift up -then remove entire drawer slide assembly.Remove plastic decorative front cover(it just snaps off) and unscrew left side drawer slide screws.replace with new part and screw in screws. Replace in bottom of fridge and replace glass shelf.So Easy that an average house wife like myself was able to do it alone.Almost as easy as finding the part needed on partselect.com! Thanks, it was much easier than apple pie.

Removed ice dispenser trim from bottom-up and then removed control panel by gently pulling up from the bottom. Removed four screws holding dispenser chute and then two screws holing flapper assembly. Replaced gnarly old flapper with a new one and put all removed pieces back together.

The same as the vidio, very easy. Thank you