GSR23YBTAWV General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Joe from Stevensville, MD
- Parts Used:
- WR55X10942C
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Continuous clicking noise, compressor was not running
Removed the old control board at the rear of the refigerator, installed the replacement board.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dan from COLUMBIA, SC
- Parts Used:
- WR55X10025
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Socket set
Refrigerator not getting cold
Replaced Temperature Sensor and now it is getting cold.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kyle from HAZEL GREEN, AL
- Parts Used:
- WR49X10091
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Refrigerator made EVERYTHING Frozen; Water line was frozen; Ice machine stopped working
This part worked marvelously. I followed a YouTube video to completion. Essentially, I removed the water filter cover by squeezing the tabs on the side. Then, I removed the housing for the light based on the tabs placement. I unscrewed the lighting fixture, unplugged and set aside. After that, I removed the bottom part of the damper assembly (that's not included but virtually attached to the damper) by pulling on its tabs' placements. Then, I pulled off the damper assembly, unplugged the cords and added the new assembly WITH the inclusion of the damper gasket assembly that doesn't seem to have been a part of the old assembly. Rescrewed and reattached everything and now the fridge is as good as new!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ron from QULIN, MO
- Parts Used:
- WR49X10091
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Fridge side was getting to cold
Found this site on the web. Told them my problem. They told me the most common part failure. I purched the part. Installed it per instructions. Waaa la now have a working refrigerator thank so much. U got the wife happy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jimmy from SHONGALOO, LA
- Parts Used:
- WR49X10091
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Refrigerator side was freezing all the fresh vegetables in all three of the crispers...even the milk and all drinks were freezing..
Went online and read all the problem an found it could be my Air Inlet Kit...did not know it had one ..was online and ordered it...came in couple days..
to replace the damper I just remove the light at the top of the frige and the cover around it .I also removed the filter and filter cover..then the damper assembly only has 2 screws .I removed top three glass trays for more room...was a little easier than I was expecting..just about 30 minutes to hour ...(1) unplug Ref and last (plug it back in). Thanks ...
to replace the damper I just remove the light at the top of the frige and the cover around it .I also removed the filter and filter cover..then the damper assembly only has 2 screws .I removed top three glass trays for more room...was a little easier than I was expecting..just about 30 minutes to hour ...(1) unplug Ref and last (plug it back in). Thanks ...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Shelby from Sturgis, SD
- Parts Used:
- WR55X10942C
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Ice and water dispensers were not working, Control board was making a clicking noise.
Disconnected power, removed screws from cover on back of refrigerator, unpluged wire connectors, squezzed four support fasteners and removed old board. Put new board on support fasteners, reconnected wiring, replaced cover, pluged power back in, turned controls back on. It wored fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fred from Vineland, NJ
- Parts Used:
- WR55X10942C
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Circuit Board was clicking and refrigerator was not working properly
narrowed it down to the circuit board...removed cover panel after unplugging frig. read directions thouroughly.... removed cables attached to old board. this is the tricky part removing the board from the plastic clips....broke two pulling old board off popped new Board onto remaining plastic mounting clips and reattached cables plugged frig in and got a shock as my shoulder touched the board. everything seemed to be working and but cover back on....viola all done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rick from Vacaville, CA
- Parts Used:
- WR12X10626
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken shelf face
+The shelf face has little plastic locator clips that snapped off. the shelf face just comes off with a light lift of these two clips and a slight upward pull then lift up and off. The new one slips on with the top slipping onto the top rail of shelf, then push the bottom tow clips over the bottom rail of the shelf. There you have it smooth as glass.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anthony from Yardley, PA
- Parts Used:
- WR55X10942C
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Freezer and refrigerator would get warm, followed by it getting cold again, doing this numerous times throughout the day.
After determining it was not a problem with the defrost cycle, ( this refrigerator had no separate defrost timer), I ordered the main circuit board with the hope that the relays built into it were hanging up and not properly turning on the compressor, (a chattering sound could be heard). Ten screws to take the access cover to the board off and a few connectors later and it was as good as new. Took about ten minutes!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from LK HOPATCONG, NJ
- Parts Used:
- WR71X10761
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Broken self insert
It clips right in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Silvia from KANSAS CITY, MO
- Parts Used:
- WR71X10761
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
Broken shelf insert
It was a bit hard to pop it into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from MOUNT VERNON, IL
- Parts Used:
- WR71X10973
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The bottom was cracked
Just replaced it with new part
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lynn from RCH PALOS VRD, CA
- Parts Used:
- WR71X10761
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
My shelf inserter broke into pieces.
It was very easy to install and fit right into the shelf.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from NORTH PALM BEACH, FL
- Parts Used:
- WR24X10155
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
door gaskets developed mold which could not be removed
out with the old
in with the new
in with the new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carlos from Copper Canyon, OK
- Parts Used:
- WR09X10107
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Start relay burned
Unplug the refrigerator removed the condenser/ compressor cover back bottom on fridge, remove the relay from the compressor took off the two wires, replace with new relay
Was this instruction helpful to you?
Thank you for voting!