TFXC20RRAWH General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- bert from Spartanburg, SC
- Parts Used:
- WR2X4901, WR13X10020
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
door would not close, had dropped down.
Was able to pull the door up to the normal position, then blocked in place with 2 2x4's. Easily removed the hinge assemble and the door closing cam, which had broken in two.
bolted on the replacement parts in 10 mionutes and the door was a good as new: peice of cake!!!
bolted on the replacement parts in 10 mionutes and the door was a good as new: peice of cake!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wilbur from Waynesboro, PA
- Parts Used:
- WR13X10020
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Wrench (Adjustable)
Freezer hinge was worn
Shut off water and disconnected at factory joint at bottom hinge. Unplugged the electrical at the top hinge. Removed the door and installed new bottom hinge and cam assembly. Reinstalled the door and hooked water and electric back up. Part worked fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from Lafayette, NY
- Parts Used:
- WR13X10020
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Cams on Hinge assembly broken, door didn't close properly
I supported door with 2* 6 scrap wood. I used cedar shingles to raise door to correct height.
Using a socket wrench, I removed the hinge from the fridge and the cam assembly from the door.
I installed the new hinge and cam using the shims thatwere behind the original parts.
I removed the 2*6 supports and the door now works perfectly.
Using a socket wrench, I removed the hinge from the fridge and the cam assembly from the door.
I installed the new hinge and cam using the shims thatwere behind the original parts.
I removed the 2*6 supports and the door now works perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dean from Park Ridge, NJ
- Parts Used:
- WR49X10183
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
rusty ice maker
removed old parts and installed new. went smooth
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Miami, FL
- Parts Used:
- WR17X4310
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The Auger in the Ice became Rusty
Once I received the New part, I simply removed the old one, unscrew the door assembly off of the old one and reinstall it on the new one using only 4 screws. Then simply pluged in the New Ice Bucket. If it were any easier, My Kids would have done it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wallace from Detroit, MI
- Parts Used:
- WR17X4310
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Part of my ice bucket assembly had broken off
All I did was take the old bucket out,, which had been frozen to the base, and I had to thaw out, by turning the refrigarater off , and use a hair dryer to melt the ice, after that I unscreewed the outer face of the old bucket, and replsced it to the new bucket
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ron from Clinton, MO
- Parts Used:
- WR57X10033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
no water to icemaker
turned off water supply, took screws out of bracket, then unhooked water lines. Installed water lines onto new valve, plugged it in then screwed bracket back onto fridge, turned on water and was back operating
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- robert from FRANKLIN SQ, NY
- Parts Used:
- WR23X37285
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
light not working
I used pliers to pull lightly on the head of the switch, while I inserted a small flat head screw driver into the base of switch and gently worked around the edges to free it from the panel.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bobby from SENECA, SC
- Parts Used:
- WR13X10020
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Refrigerator door would not shut
Removed old hinge assembly, bolted on new assembly-door shut like new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from St. John, MO
- Parts Used:
- WR17X2740
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Rust on Metal auger leaving rust in ice...
Disassembled front door/cover (3 screws), then removed deflection door assy, (4 1/4" nuts), CArefully and methodically removed C Clip and grinder teeth...Be careful with this step to document/remeber how to re-assemble! Auger repleced then reverse steps...
All in all, not too bad, but you can easily screw up the teeth re-assembly.
All in all, not too bad, but you can easily screw up the teeth re-assembly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ron from ORANGE, CA
- Parts Used:
- WR30X10093
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Unit had stopped making ice
Ordered the icemaker replacement. unplugged the unit, followed the simple instructions and got it done in less than 30 minutes. It did take a LONG time to start making ice. But it's working now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Provencal, LA
- Parts Used:
- WR57X10033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
ice maker barely working
Repair was very simple. Removed refridgerator bottom back panel, about 6 or 7 screws. disconnected bad valve, installed new valve , connected water supply line and then reinstalled panel. Took about 15 minutes from start to finish.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from CONCORD, CA
- Parts Used:
- WR50X55
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Unit would not terminate defrost cycle resulting in melted frozen food
Turn of power to fridge. Removed all shelving in freezer section. Unscrewed back panel from freezer area. Removed old defrost term t-stat from top of evaporator coil assembly. Cut existing two wire leads, spliced in new T stat wires. sealed wire splices from water egress and clipped new t-stat in same position as old one. Reassembled rear panel, installed shelves. Turned power back on.That's it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chip from Mandeville, LA
- Parts Used:
- WR30X10093
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
broken auger in the bucket assembly.
I ordered the wrong part, the ice maker assembly, because your diagram was not marked properly. I returned the part and you credited my account. Thanks. Ordered the new bucket. It worked fine. Now I have ice and crushed Ice whenever I want. Thanks.
p.s. I didnt use any tools, but to satisfy you I select nut driver.
p.s. I didnt use any tools, but to satisfy you I select nut driver.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce from Mobile, AL
- Parts Used:
- WR2X4550
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Drive cup broke due to ice cube jamming it
Remove three screws insert part; manually checked out drive and waited for ice to buildup and it worked like new.
Was this instruction helpful to you?
Thank you for voting!