GSR23YBWASS General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Gerald from Shelton, CT
- Parts Used:
- WR82X10103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
brand new ge refrigerator delivered with broken access cover. cost 6.95 so i repaced it myself.
removed 6 screws and repaced cover.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cyndy from Rancho Cucamonga, CA
- Parts Used:
- WR23X31507
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
I dropped one of the trays and it hit the light switch and broke off!
It was so darn easy! Took less then 10 minutes to fix. Self explanatory no instructions needed! Very cool!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rodney from Dallas, TX
- Parts Used:
- WR55X10942C
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Relay on motherboard was clicking-Quit cooling
Followed the partselect video on how to replace motherboard and the video described the exact replacement procedure.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from Littleton, CO
- Parts Used:
- WR23X31507
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The Light Would Not Go On
Knew the switch was bad. Researched on the internet how to fix. Used a steak knife to pop the old one out, changed the contacts to the new switch and popped it back in. It took longer to open the box than it did to replace the switch. And the part arrived 2 days after I ordered it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ron from Bonney Lake, WA
- Parts Used:
- WR55X10942C
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
would not regulate temp.
replaced main board.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Pacheco, CA
- Parts Used:
- WR55X10942C
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
The evaporator fan in the freezer would slow down and speed up for a long period of time before eventually shutting down at the end of a cooling cycle.
Tom Paone at [email protected]. was very helpful at recommending that a solution to my problem was to replace the ASM Main Domestic Motherboard. I ordered and received the board in two days from PartSelect. After unplugging the refrigerator I used a nut driver to remove the three screws that held the motherboard cover in place and then disconnected all of the connections to the board. Next, using a pair of needle nose pliers, I gently squeezed on the white plastic anchor retainers that fastened the motherboard to the refrigerator. While doing this at each anchor I gently pulled on the motherboard until it was separated from the retainer anchor post. There were four retainers total. I removed the old board and in the reverse order installed the new board. All of the connectors were easy to match to the new board because the wiring connectors coming out of the back of the refrigerator were only long enough to hook to the correct connectors on the circuit board. There was an extra connector that I didn't use on the new board and also the connection for the ground wire used a ring connector instead of a spade connector. To remedy this I simply used the ground wire assembly from my old board. I also took the time to remove the lower cover on my refrigerator and cleaned the condensing coil with a vacuum cleaner. The total time to replace the motherboard and clean the condensing coil was about 20 minutes from start to finish. This repair solved the problem with my evaporator fan. A big thanks to Tom Paone at [email protected]. for helping diagnosis my problem and suggesting the correct replacement part. I saved between $100.00 to $150.00 not having to call out an appliance repair person to fix my refrigerator.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- WILLIAM from YUMA, AZ
- Parts Used:
- WR55X10942C
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Frige stopped cooling completely
i Removed back panels and then I removed the faulty circuit board. Installed new circuit board and presto everything worked. I can't believe how easy it was but on the other hand I couldn't believe a refrigerator had such a sophisticated part..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kyle from Norwalk, IA
- Parts Used:
- WR55X10942C
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
whining noise coming from GE refrigerator
It was a very simple installation after reading about everyone else having the same "noise" problem with their GE side by side refrigerator.
I simply; pulled the refrigerator out, turned off the power, took off the 3 screws to remove the plate, unhooked the 5 or so connections with my hands, put the new part in, hooked the connections up, put the plate back on, plugged the refrigerator back in, and slid in back into place. It took around 10 minutes to do, very simple.
I simply; pulled the refrigerator out, turned off the power, took off the 3 screws to remove the plate, unhooked the 5 or so connections with my hands, put the new part in, hooked the connections up, put the plate back on, plugged the refrigerator back in, and slid in back into place. It took around 10 minutes to do, very simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- scott from washington, NC
- Parts Used:
- WR55X10942C
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
freezer would freeze then thaw
diagnosis, fan would run more than normal, compressor would only come on sometimes, check line voltage to the mother board (yes !!! a mother board with a relay for the compressor built onto it )! check the switched voltage out to the compressor. If a/c 115 in but no a/c 115 out while the fan is on replace the mother board. Remember this is a LIVE VOLTAGE TEST, BE CAREFUL HOW AND WHAT YOU TOUCH YOUR LIFE IS NOT WORTH SAVING A REPAIR BILL !!!
I suppose if if went long enough in this condition the result would be fan runs a lot but it does not get cold.
Hope this helps
God Bless
Captain Scott Cousins
I suppose if if went long enough in this condition the result would be fan runs a lot but it does not get cold.
Hope this helps
God Bless
Captain Scott Cousins
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- robert from melrose, IA
- Parts Used:
- WR55X10942C
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
deep freeze defrosting and frig. getting warm shortly after stoped cooling completley
Received main board in less than two days. back of frig. small panel removed 3 screws, removed cover exposing main board with needle plires squeesed 4 plastic tips to release board unpluged conectors, reinstaled new board, worked perfict. Thank you for your helpfull web site. Bob.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- HECTOR from INGLESIDE, TX
- Parts Used:
- WR55X10942C
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Faulty Motherboard
Disconnected power at outlet. Removed three screws from access panel. Disconnected six electrical connections, compressed three plastic retaining pins and removed board. Installed new board and reconnected connections, installed three screws on access panel and turned the fridge on. No more crazy evaporator motor noise
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from NORTH PALM BEACH, FL
- Parts Used:
- WR24X10155
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
door gaskets developed mold which could not be removed
out with the old
in with the new
in with the new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rick from Vacaville, CA
- Parts Used:
- WR12X10626
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken shelf face
+The shelf face has little plastic locator clips that snapped off. the shelf face just comes off with a light lift of these two clips and a slight upward pull then lift up and off. The new one slips on with the top slipping onto the top rail of shelf, then push the bottom tow clips over the bottom rail of the shelf. There you have it smooth as glass.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from PALMYRA, VA
- Parts Used:
- WR23X31507
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
The switch was loose ( no spring). The lights did not work.
Unplug the refrigerator. Gently pry old switch out with screw driver. Move wires to connector on new switch with needle nose pliers. Pop it back into the hole. Plug back in. Peek inside to see the lights working.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from MOUNT VERNON, IL
- Parts Used:
- WR71X10973
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The bottom was cracked
Just replaced it with new part
Was this instruction helpful to you?
Thank you for voting!