GSHF9NGYBCWW General Electric Refrigerator - Instructions

Just fallow video shows that it 123 !

I had previously removed the motor by unplugging 2 plugs and had the motor sitting on my kitchen counter awaiting for the part from the site. On receipt of the part, we removed the broken left glide, installed the new glide, re plugged the motor and attached it to the new glide. If it weren't for my hubby trying to find the right socket tool for the screws, installation would have been less than 15 minutes. The screw that attaches the glide to the ice motor is a different size than the ones that screw into the side of the fridge.

Opened package and just snapped in front insert. Took longer to open package than it took to replace broken insert.

Amazingly simple. I followed the directions I found on your site 4 socket screws removed. They were easily accessible. Replaced the broken bucket guide with the new part. Put the screws back in in less than 15 minutes the icemaker auger feature that dispenses the ice was back in working order.

We actually followed the instructions of the video for the installation of the dual inlet valve and it was incredibly easy to perform. The fridge works perfect again!

I was able to snap the new piece right in

Removed the lower 2 drawers, lower front grill, rear lower compressor cover. Removed the 2 water lines from the quick connects and screws from the water tank. Pulled lines through the hole in the right rear of the refrigerator and removed tank. Then reversed steps to install new tank. The upper plastic tank cover has 2 buttons on top that are really screws with a plastic cap, these are easily removed with pliers.

Of course being a women to say I repair my refrigirator is very self gratifying specially when share with other womens like me divorce,having to do on their own, great site, very simple explain on the video with words I could understand, no surprices right to the penny. I save a lot of money, thank you so much, i recomend the site to anybody.

Removed four screws from broken glide bracket and auger bracket and remove. Replaced with new glide bracket and reinserted ice bucket to connect auger with auger motor. Two socket size job.

I got the model # off the fridge, ordered the part online. The part was fairly cheap and was at my house 2 days after I ordered it. It was the exact part and I installed it in about 15 minutes and everyting worked out fine and easy and cheap, under $15 total to fix the issue. All I needed to do was use a flathead screwdriver to "pop" out the old switch, remove the 2 wires off the wire connection points, put the wires on the new switch and push it back into place. easy. Great place to get exact parts and fast shipping.

My father called and asked me if I knew where he could get a new switch light for his refrigerator. I came across your web site and found the part right away. In less than 3 days the part came and my father put it on. He said it was easy and that it was great to have the part come to him instead of having to search all over town. Thanks so much for the fast, easy service.

I located the light switch at the bottom of the area where the door closes. I just popped it out with a small screwdriver and installed the new switch. A 2 wire connecter and small clip is all there is to it.

Really simple... broken light switch easily removed with flat edge screw driver. Once removed unplug and plug new one in and good to go.

I pulled the bulb out to see if it was the bulb, no! I took the switch out, of course with the refer unplugged, and jummped out the wires and the light came on. Ordered my switch and put it in in 10 seconds and then there was light! Thanks again for showing me the light!

Tim in NJ

I turned water off at valve and unplugged refrigerator. I removed screws to remove cardboard cover at bottom. I removed screw holding duel inlet water valve bracket and pulled out valve. Then it's just a matter of exchanging electrical connections and water lines. The electrical connections unplug and plug in-red to red and blue to blue. The water lines are two different sizes so they can't be mixed up. Then reattach bracket and cardboard cover. Turn water back on and plug back in.