PSI23SGMBKBS General Electric Refrigerator - Instructions

Replaced flapper. Followed the video. The lamp caused the removable plastic bracket (which supports the control panel and the ice chute) to fuse with the plastic frame in the door. Eventually broke the fused plastic, removed the bracket, and filed the rough broken plastic before reassembly.

We had problems with the ice dispenser chute building up frost from condensation freezing due to the flap not closing properly. It would clog up completely and often. I had already replaced the flap and spring years ago but it didn't help much. I Googled this problem for my model and found a video detailing how to check and change the solenoid. Sure enough, the solenoid was completely corroded and crumbled in my hands as I removed it. I ordered the replacement part and made the repair myself. The video was perfect in describing. If your refrigerator is well used as ours is, you'll be shocked by the buildup and cleaning that will be necessary as you make this repair. I ended up taking much more of the dispensing assembly apart so I could clean it with warm soapy bleach water. Be mindful as you disassemble or take photos / videos with your smartphone to help put it back together. It took longer to clean than replace the solenoid. Also, be careful if you have an island or other cabinetry close by. If you have to pull the refrigerator out to unplug it, the handles can chip granite edges or the top corners can scratch wood work. We have cherry cabinets that surround ours. I chipped the edge of the granite when I pulled it out and I scratched the wood as I pushed it back in place. Minor repairs but can save you some frustration. Good luck!

just watch video simple

removed the control panel ,using a paper clip, removed five screws, disconected wire connector, and removed the solenoid. reversed procedure to reassemble. ordered the part one day and received it the next day. Thank you for the prompt response.

I followed the instructions on a posted desctiption. It workded perfectly. Replacing the inner door panel was not as difficult as described. Just start the process with the screws in the middle of the door. Those two screw holes were not slots. All of the remaining screw holes had slots. I installed all of the door screws before tightening any. I workded right the first time.

Opened, discovered not flapper but more complicated

no instructions came with the part so I wrote for help from your techs. They were able to tell me how to access the solenoid. From there I was able to figure the rest out. I had to remove the trim, electrical board, flap, springs and arm to reach the screws necessary to remove the solenoid. I removed some of the corrosion with a baking soda paste so I could remove the screws. I carefully noted each step and position of the parts I removed and reversed the process to put things back after replacing the solenoid.

The video to replace the flapper looks easy, howerer the first step is to remove thestic cover of the icemaker. In my refrigerator model (as oposed to teh one shown n teh video) teh coved if firmly attached and goes under the refrigerator external plate so I was never abel to take it oot (so step 1 failed).
I was able to replace the flapper TROUGH the whole whre te ice comes from! this took lots of patients and someone with small hands!

Removed front panel and control touch pad to access solenoid and door recess assembly.
Replaced solenoid and door recess assembly. Didn't need spring and crank door.
Wish you could have supplied new screws, as the original are very corroded and I can't find them atv any hardware store.

Thanks

First remove trim surrounding ice/water dispenser assembly. Use a flat spackle knife to obtain space between door and trim. Be careful not t scratch refrigerator door. Then pry trim off. This was the most difficult part of repair. The front plate of the dispenser is held to the back of the dispenser by two friction fastners and in the case of my refrigerator a phillips screw (some don't have screw in middle). Use a small round tool like an allen wrench to push up on the 2 fastners to release them. Next push the front assembley aside and remove the 4 screws holding the back part of the dispenser. Push that assembly aside. Remove the defective solenoid assembly by removing the 3 mounting screws. The solenoid base can be worked out by slipping it out of the solenoid assembly plunger still attached to the dispenser door assembly. Next slide the plunger off of the dispenser door assembly. Install new solenoid assembly by reversing this procedure.
Hint - I found the ice door assembly (wr17x11653) also needed replacement and it is well worth the effort to replace both at the same time.

We followed the instructions we found on this site.

First we unplugged the refrigerator.

Then we removed the control panel that has the ice type selection on it by releasing the three spring latches. These are accessible from the bottom of the panel looking up toward the ice dispenser. There are three holes. Press a narrow screwdriver or punch in each of these holes and then pull out the control panel. (Be careful not to disconnect the wires, but observe how the wires are routed.)

Then we removed the ice tube cover that covers the solenoid assembly. There were four screws. One was very rusty and it required some WD40 to loosen it. Once the cover was removed the solenoid was visible on the right. (It has a floating component that attaches to the "arm" of the flap. This is how the solenoid opens and closes the flap. The flap needs to close properly so ice does not build up in the door.)

There were three screws that had to be removed to get the solenoid out. (The top one you may just need to loosen once the bottom two are removed.) When the solenoid was removed we also removed the old floating component from the flap are and replace it with the new one. We slid this into the solenoid hole and then screw it in with the three screws.

Before we attached everything, we plugged in the refrigerator to test the solenoid. We dispensed some ice and waited to hear the flap close. (The flap close is slightly delayed so be patient.)

We attached the cover that was over the solenoid being careful to route the wires as they were when we started. We test the solenoid again. Then we snapped the control panel back into place and tested again.

We found that having the right size screwdriver made a difference especially dealing with rusty screws. It was also handy to have a good flashlight. Having extra hands was helpful to hold the control panel and cover while working on the solenoid and routing the wires.

1. Use skewer to press plastic tabs under control panel, 2. Remove control panel and unplug solenoid, 3. Unscrew dispenser assembly and solenoid screws, 4. Press in tabs on lamp and remove assembly - unplug, 5. Replace lamp assembly, 6. Replace solenoid assembly and fasten screws, 7. Replace flapper. 8. Replace other parts in reverse order.

This time I did not make repair. I have purchased only to have spare parts. I have changed this parts recentely and I think this parts are not strong enough to work more than two or three years.

Removed access panel on freezer door, removed circuit board, removed and replaced solenoid, reinstalled previously removed parts

Turn off power
Remove operator faceplate by pullling out on outer lower corners
Disconnect wire connectors from circuit board
Remove four screws from dispenser and pull out dispenser assy
Replcae Door ASsembly
Put everything back in place
Power up
Job Done