PSI23SGMBKBS General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- NICK from COCOA bEACH, FL
- Parts Used:
- WR62X10055
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Ice dispenser door will not shut completely
I removed the door cover plate and disconnected the circuit board, then four screws. The part was corroded in place. Upon removing three screws and cleaning the surface, the new part was an exact fit, replaced it and everything works like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from W Berlin, NJ
- Parts Used:
- WR62X10055
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Ice forming around shoot. Flapper door not shutting letting warm air in.
I followed they instructions from the other "do it your selfers" but only replaced the solenoid. This was the cause. Rust was keeping solenoid plunger from moving and this held the flapper door open. Very easy to repair!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carla from RUSSELL, KS
- Parts Used:
- WR01X37886
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Light bulb burnt out
replace a new blub
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from TYLER, TX
- Parts Used:
- WR62X10055
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Your video was wrong. Your step was to remove exterior frame on ice/water outlet. No need to remove.Wasted too much time trying to remove.
Remove control panel.
Remove four screw in control panel bracket.
Remove to bottom screws at bottom of solinid loose top screw.
Replace all screws.
Remove four screw in control panel bracket.
Remove to bottom screws at bottom of solinid loose top screw.
Replace all screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from BRICK, NJ
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
My ice container and Ice chute were freezing up and getting blocked, and my filtered water line was also freezing
I just followed the instructions on the video and it was exactly as they said......no surprises.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jeff from stillwater, OK
- Parts Used:
- WR62X10055
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
solenoid quit working
repair was easy, just removed control panel and removed screws from solenoid, switched out with new, was done in minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Sandy Hook, CT
- Parts Used:
- WR62X10055
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Ice chute wouldn't open or shut correctly - rusted solenoid
Replaced rusted solenoid.
Popped front button panel off from the bottom using flat head screwdriver; Removed 4 screws holding electronics board and disconnected wires. Unscrewed 3 phillips head screws on old solenoid and replaced with new part. Reconnected wires to board, screwed back in, and pushed panel back into to place.
Thumbs up to PartSelect - fast, straightforward service and fast delivery.
Popped front button panel off from the bottom using flat head screwdriver; Removed 4 screws holding electronics board and disconnected wires. Unscrewed 3 phillips head screws on old solenoid and replaced with new part. Reconnected wires to board, screwed back in, and pushed panel back into to place.
Thumbs up to PartSelect - fast, straightforward service and fast delivery.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Philip from S BURLINGTON, VT
- Parts Used:
- WR17X11653
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Remove front cover
Remove front cover did not remove wires remove ice and water unit took off flapper put new one on 5 minutes back together
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from Rogers, AR
- Parts Used:
- WR17X11653
- Difficulty Level:
- Difficult
- Total Repair Time:
- 30 - 60 mins
Watched video on flapper assembly replacement looked real ready. Video failed to mention ice dispenser trim was glued in place . Had to buy real small paint scrapper that would fit in dispenser outlet to free inside edge of trim piece. Once I got it all loose job went very easy.
Use small putty knife to cut internal sealant on ice maker door trim piece. Then you can easily remove it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lary J from Destrehan, LA
- Parts Used:
- WR02X11330
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Plugged water line reservoir
Turned water supply off; pressed dispenser sw to release presure ; cut tubing holding reservoir ; nuit driver to release screw holding reservoir and pulled out ; took outside and used hose nozzle to try to clear; did not clear at first then took weedeater string and disloged something and water flowed freely; turned out had to change waer solenoid valve (both) as the one for the water dispener was also plugged which did not show up before.
P.S. Had back flow water thru system before and changes of parts. Water flowed freely.
P.S. Had back flow water thru system before and changes of parts. Water flowed freely.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Fishers, IN
- Parts Used:
- WR62X10055
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Ice Maker Door fails to close
1. Remove outside panel (snaps off)
2. Remove Control panel 4 screws
3. Remove Solenoid by taking out 2 bottom screws
4. Remove solenoid weight from crank lever
5. Place new solenoid weight from crank lever
6. Insert weight in solenoid
7. Place back 2 bottom screws solenoid
8. Place back Control panel screws
9. Snap back into place outside panel
2. Remove Control panel 4 screws
3. Remove Solenoid by taking out 2 bottom screws
4. Remove solenoid weight from crank lever
5. Place new solenoid weight from crank lever
6. Insert weight in solenoid
7. Place back 2 bottom screws solenoid
8. Place back Control panel screws
9. Snap back into place outside panel
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DALE from OLATHE, KS
- Parts Used:
- WR62X10055
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Ice machine trap door not opening or closing
Fairly simple fix. You must first uplug refrigerator, then take off the inside freeze door panel, approx. 25 screws. Then you must take out the trap door assembly approx. 6 six screws. Pop off the LED panel, requires the use of a flat blade screw driver to pop it off. Remove solenold by removing 3 screws, replace with new solenold.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from HAYMARKET, VA
- Parts Used:
- WR17X11653
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Flapper was worn and misshapen allowing warm air in freezer, ice cubes to melt and drip and impairing function of ice dispenser. Frost formed in ice dispensing chute also.
Followed the online video. Unplugged refrigerator, removed trim piece, lifted control board cover, removed 4 screws retaining circuit control board and removed the 3 connectors from the control board. Located flapper and removed by using small flat tip to take tension off flapper connectors. Helper held flash light to illuminate flapper connectors. Reversed procedure. New flapper seals well and cured problems. Circuit board was a bit different than one in video, but still had the 3 connectors. Marked each connector with grease pencil at top edge to ensure correct reconnection. Should note how wires are threaded around circuit board to ensure they are tucked back in correctly in reassembly. Remove trim piece carefully. I broke 2 of the 8 plastic pins that hold trim on. May be due to age of unit as they were brittle. 6 pins still hold trim piece flush.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ERIC from THE VILLAGES, FL
- Parts Used:
- WR62X10055
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Flapper Door stuck open
The only tricky part was removing the front panel. Releasing the latches required considerable force. The best tool I found was a "jack knife" type Allen wrench set, using the medium size wrench, which fit into the release hole and upward pressure did the trick. The rest of the job was very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Maurice from PALM BCH GDNS, FL
- Parts Used:
- WR62X10055, WR17X11653
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Socket set
Ice dispencer door does not close properly causing ice formation
Used the instruction provide by Part Select, which are easy to follow.
When it came to replacing the Solenoid, the two bottom screws were easy to remove, The third screw (located on the top) needed lo be loosened, That screw was very difficult to remove because it was rusted, and I had to replace it.
I suggest that a spare screw should be supplied wit the solenoid.
When it came to replacing the Solenoid, the two bottom screws were easy to remove, The third screw (located on the top) needed lo be loosened, That screw was very difficult to remove because it was rusted, and I had to replace it.
I suggest that a spare screw should be supplied wit the solenoid.
Was this instruction helpful to you?
Thank you for voting!