GTR22KSSCRSS General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- rodney from cave city, AR
- Parts Used:
- WR60X10220, WR60X10207
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Socket set
warm in lower area and not freezing good in freezer area
condenser fan on bottom condenser not runningchanged fan and fan motor
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Andenet from Haymarket, VA
- Parts Used:
- WR60X10220
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
Fan and housing cannot be removed together.
On partselects video the gentleman removes the fan and housing in one piece. This is a great idea but does not work on this brand of ge. I removed the fan housing screw as instructed but left it in place and swiveled it enough to access the retaining screws with a socket driver. Over all swap of the fan was seamless and the video is a gem. Andy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from Oak Lawn, IL
- Parts Used:
- WR60X10257, WR02X12008
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Very nosiy fa
I removed the ice marker first and took the back panel off using a nut driver. Be careful I had wires tied to the back panel, so I moved it like opening a door, right to left. The I removed the fan motor. Be careful not to damage the fan blades. I took the fan blades off and the dust cover. The dust cover was very tight. I had to use a very small screw driver to get it off. When I put the dust cover on the new motor I did not push it down tight. I turned the spindle of the new motor to make sure it turned. The put everything back. Turned it on and it worked. I put the ice marker on last. Take a note of how far the fan blades are on the spindle. The refrigerator now turns off more often.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- thomas from albany, NY
- Parts Used:
- WR23X10334, WR09X10104, WR02X11567, WR01X10220
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
frig ran to often
took apart stat. area rplaced wire harness &t.stat simple but im a retired union electrican so wiring was a bit easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- lawrence from N Ft Myers, FL
- Parts Used:
- WR60X10257
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
needed new Evaporator Fan Motor
Follow the instructions on the video. Took pictures removing Evaporator Fan Motor. Installed new motor in 44 minutes. Thank you part Slect
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from York, PA
- Parts Used:
- WR60X10220, WR60X10207
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Freezer not cold, Frig cold enough, runs all the time, Hot to touch in spots.
My compressor fan that blows over the coils was not spinning. I measured 120 VAC going to the fan so I knew it should have been spinning but wasn't. Took fan motor out and took it apart and super lubed the motor to get it spinning again temporarily until I could get the new one in. Put new one in and has been working for about 10 days now. Freezer is not below 0 deg F which is what you want. Frig is below 40 deg F also what you want.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kirk from Springfield, MO
- Parts Used:
- WR60X10220
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Socket set
Condenser Fan was shot.
I followed the instructions in the video regarding removal, repair and reinstall. It all went as the video said, except for the reinstall. The rear tab did not snick into place like the one in the video did, and it was extremely difficult to see whether or not it was inserted properly. I ended up inserting the rear tab by feel, and then I had to hold it in place while I stretched the front part of the frame to line up the screw hole in order to reinsert the screw. I had to have my wife hold the flashlight while I did that in order to see. Other than that, the repair went well, it is working like a charm, and I know I have a quality GE part in my refrigerator again! Many thanks to Partselect for their speediness in getting the part to me and giving me the needed information in getting the repair done! I will shop here again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john from Marquette, MI
- Parts Used:
- WR60X10257
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
fan did not work
Removed plastic housing and metal back panel,then removed fan motor and reinstalled everything. In all it took about 20 minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Raton, NM
- Parts Used:
- WR60X10220
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Condensor Fam Motor Noise
When the condensor fan motor started making those "Dying Mouse" noises I knew it was time to replace it. So I removed the fan motor and re-oiled it's lubricating packing, reinstalled it and promptly ordered a repacement moter online from PartSelect. I've ordered parts from them in the past with great results and rapid shipping. So now the "Dying Mouse" has been evicted and my wife is happy. And everyone should know, ( If Momma ain't happy, Then nobody's happy.) Thanks again PartSelect for your fast, reliable parts source with very reasonable prices.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- richard from castle rock, CO
- Parts Used:
- WR60X10220
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Fan Sqeels
Remove back panel . Removed fan shroud. Replaced fan and panel. Ops ck ok so far
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MICHAEL from Lubbock, TX
- Parts Used:
- WR60X10220
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Fan wasn't running and walls of freezer and ref. were hot
took screw that holds motor frame in place out with nutdriver, rolled motor frame out after unplugging motor,took screw out of strap that held motor in frame, removed bushings from old motor and put them on the new one and re3versed the proceedure.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Dayton, NV
- Parts Used:
- WR60X10257
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Made a lot of noise
Remove plastic parts then remove back panel, remove plastic seround holding motor, romove 2 screws holding motor bracket, unplug motor, reinstall motor, bracket, seround, back panel DONE
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- paul from east hanover, NJ
- Parts Used:
- WR23X37285
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
refig light did not work
per your instructions
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ANTHONY from NEW EGYPT, NJ
- Parts Used:
- WR23X37285
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
sticky switch
easy pry out, disconnect wiring, connect on new switch and press in switch.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- TREVOR from KENT, WA
- Parts Used:
- WR72X10072
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench set
broken slide drawer track
Took out shelf, unscrewed old track, screwed on new track. Only thing is not a standard flat or Phillips screw head so if you don't have a star head bit, you are out of luck.
Was this instruction helpful to you?
Thank you for voting!