GTR22KSSCRSS General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Kenneth from Rowe, VA
- Parts Used:
- WR2X9391
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
bulb out
I ordered the part, within two days we had received it. My husband put the part in and I really don't know what he used doing so. All I know is that the light works now and we don't have to use the flashlight. Thanks a lot.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ted from SANDWICH, IL
- Parts Used:
- WR23X37285
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broken light switch
took a little more effort than the video show to remove old module and replace new. Works fine now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ED from ENON, OH
- Parts Used:
- WR2X9391
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Short in the light socket.
Un Plugged the frig. Unlocked the socket by pressing down on the latch. Pulled the socket out ensuring I had enough slack. Unplugged the old socket installed the new. Plugged the frig back in. Tested the switch . Very easy-to-use.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephanie from KEARNY, NJ
- Parts Used:
- WR23X37285
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light was flicking
It was way to ez to install only a couple of minutes that's it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Louis from LEAGUE CITY, TX
- Parts Used:
- 40A15
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Change bulb
Easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roscoe G from ROCHESTER, NY
- Parts Used:
- 40A15
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Light burnt out.
Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Don from Eugene, OR
- Parts Used:
- WR23X37285
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The door activated light switch was missing.
Pulled the two wires out from the access hole in the lower part of the refrigerator. Put them in the spade connectors on the new switch, and pushed the switch into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chris from Charlotte, NC
- Parts Used:
- WR2X9391
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
socket had melted
pluged the wire harness into the new socket from the back and snaped the socket in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wayne from Issaquah, WA
- Parts Used:
- WR2X9391
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Light socket missing in refrigerator
Frig parts had been scavenged in an apartment complex. Restoring socket was only a matter of plugging in two spade contacts and clipping in socket.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia from Sylva, NC
- Parts Used:
- WR23X37285
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Bad switch for door prevented interior light from coming on
Just as your video described, although due to the age of the fridge, it took a bit longer to remove the defective switch. Your video made this so simple, I can't imagine why we lived with a dark fridge for so long! I was ready to buy a whole new fridge, as repairmen are often nonexistent for small repairs. I am the biggest fan of your company & it's repair video. THANK YOU SO MUCH
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Victor from Fort Myers, FL
- Parts Used:
- WR23X37285
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
light in freezer section not working
Using plyers Pulled old switch down and out. Put new one in and pushed new switch up into position. The switch plugs into the contacts, no wiring needed. Worked like a charm. You saved me 200 dollars GE repair bill. Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from York, PA
- Parts Used:
- WR60X10220, WR60X10207
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Freezer not cold, Frig cold enough, runs all the time, Hot to touch in spots.
My compressor fan that blows over the coils was not spinning. I measured 120 VAC going to the fan so I knew it should have been spinning but wasn't. Took fan motor out and took it apart and super lubed the motor to get it spinning again temporarily until I could get the new one in. Put new one in and has been working for about 10 days now. Freezer is not below 0 deg F which is what you want. Frig is below 40 deg F also what you want.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- rodney from cave city, AR
- Parts Used:
- WR60X10220, WR60X10207
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Socket set
warm in lower area and not freezing good in freezer area
condenser fan on bottom condenser not runningchanged fan and fan motor
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- TIMOTHY from SPRING VALLEY, CA
- Parts Used:
- WR60X10220
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
no ice being produced & on Hot point dbl sided frig panel between freezer & frig very warm
Water still came out the front when pressed, but no ice. After removing the Ice container, & the top shelf I noted the icemake inlet was iced over. I turned off the icemaker, turned down the freezer temp, & allowed Ice to melt, but problem returned. I next removed the back bottom cover & cleaned the condenser coils, & drain pan; they were extremely dirty. Then I noticed the condensor fan was not on. After getting the nomenclature plate info off the condenser fan motor I left the back cover off, & put an external fan to blow on the coils as a temporaty fix until I could get the part & replace it. During that time the refrig functioned normally. 3 days later my condenser fan motor I ordered from Parts Select arrived & I installed it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john from Marquette, MI
- Parts Used:
- WR60X10257
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
fan did not work
Removed plastic housing and metal back panel,then removed fan motor and reinstalled everything. In all it took about 20 minutes
Was this instruction helpful to you?
Thank you for voting!