PNR22LGEBFWW General Electric Refrigerator - Instructions

it was easy. Open the fridge,untwist the old filter. Open the new filter, fill with tap water and twist in place. Run water through it for a few minutes to insure it is working and filters the water.

Frig parts had been scavenged in an apartment complex. Restoring socket was only a matter of plugging in two spade contacts and clipping in socket.

I watched the video, and noticed that they did not even turn off the water. The replacement took less than 30 seconds once the filter was filled with water.

turn off water remove back cover remove 1 screw holding water valve use wrench to remove main water line input push up holders on bottom of selinoids pull both output lines loose disconnect two electrical plugs reinstall new valve in reverse order

It was as simple as taking off back panel and disconnecting 3 tubes and and two plugs to remove old valve and attaching the new valve piece to the 3 tubes and two plugs! It actually took more time getting the panel off than making the repair AND it saved us a little over $300 as the repairman quoted a price in excess of $350 to repair it. He was actually the one to tell us to buy the part ourselves and repair it. We are thankful being able to get the part and for an honest repairman.

I was unplug the electrical,closed the water line.replaced old water outlet with the new one;and there work fine.Thanks

PartSelect helped me identify the part, got it in only a few days and I followed the easy to follow video featuring Steve. Awesome!

I went on Google to get GE Tech Manual. But really, undid screws for back plate; Dismounted (1 screw) Water Solenoid assembly; disconnected 3 water hoses into solenoid; unplug two power connectors. Then reversed the process with new Water Solenoid...works great!

Removed back lower panel, removed valve, ordered part on internet, cleaned motor and back of fridge. Most time spent was waiting for delivery of ordered part. Part received and installed in 15 minutes after reviewing instructional video included in my email verifying my order, fridge pushed back into place, waited for ice maker to refill.....DONE. So easy. Thanks guys. Job well done.

removed rear cover of Frig, found valve was cracked and leaking water. turned off water and ordered new valve. After receiving new valve, Removal and installation took about 15 minutes. Pretty easy, a no brainer.

Unscrew the mounting screw and cut the tubes as close as you can to the valve. You cannot reuse the valve as the self sealing lock washers will be destroyed once you take out the tubes. Push the newly cut tubes into the new self sealing new valves and remount. Easy Peasy!

pullee refrigerator out to get to back un pluged power took off back cover unscrewed one screw to loosen water valve unscrew water inlet line ther are two water lines in back of water valve i cut them as close to water valve as i could push the water lines that i cut off into water valve makin sure in the rigfht place they are quick disquinect just push in and ther on screwed water valve back on connected water inlet line replaced back cover pluged in power pushed refrigerator back in and was done it had to run for a little while to get the air out then worked fine

I shut the water supply and took off the rear panel.
One screw released the valve. Pulled off water lines(3) and electrical connectors and installed all on new valve. Screwed the valve and the panel back and turned on the water supply. Prior instructions on website helped. Part came in two days. This part should have never failed. Looks like the housing is two parts glued together. Glue failed after 7 years. G.E. should cover this. My warranty expired after 5 years. M.K. Boca Raton,Fl.

It was very simple. Pull the fridge back (unplug and turn off water), remove the cardboard backing and disconnect/unhook the current water valve and reverse the process to connect the new.

Unplugged fridge, and turned off water supply. Removed cover from back of fridge, followed the plastic tube down to water valve.
I unbolted the mount holding water valve in place, removed the input tubing on top by unscrewing nut. I made a note of which outbound plastic tubing went to water dispenser, and which one went to icemaker, and which side of the water valve they plugged into, and then cut the tubing very close to the old valve.
I slid the tubing into the new water valve, and I felt it lock into place, very easy. Attached the input water line and tightened the nut.
Reattached the water valve mount to the body of the fridge, replaced cover, turned water valve back on and checked for leaks (there were none).
Plugged in fridge, tested dispenser, everything worked just fine. No leaks.