PNR22LGEBFWW General Electric Refrigerator - Instructions

Unplugged refrigerator. Unscrewed back cover. Unscrewed dual water valve. Unplugged electrical connections 9red and yellow) . Shut off water valve from wall to refrigerator. Cut black tube (ice maker, cut translucent tube (water line). Connected new valve to water supply. Reconnected black and translucent tubes to new valve. Reconnected yellow and red electrical plugs. Turned on water supply plugged refrigerator back in.

shut off water supply behind refrigerator, opend line at double outlet water valve. had water there. opend line at bottom of freezer door. no water there when I pushed watervalve on door. replaced double outlet water valve. then had water at hose at bottom of freezer door. but no water at outlet. took hair dryer and heated freezer door until ice melted in hose . then everything worked fine.

Had the wife shut the water off, while I was on vacation. Came home pulled the refrigerator out. Had an issue earlier in the year with a leaking hose. Discovered the valve had many pin holes and was going to need to be replaced. Went on line to Partselect ordered on Saturday. It was easy to determine if I had the right part. Purchased and received on the following Tuesday. 30 minuted later the refrigerator was back up and running with ice and cold water. Have used Partselect before always a great experience

I found that the valve was not the problem. Check to make sure you do not have a frozen water line as I did.

changed outlet valve.not the problem.needed a new filter valve assembly.

Easy job except for moving the Refigerator but it is on rollers but it is still heavy. Unplug the Ref and shut off the water and replace the valve and the reverse the order. Simple

Unplugged the unit and turned off the water line to the refrigerator. Removed the six screws holding the back cover. Removed the screw holding the outlet water valve. Unplugged both electrical connectors. Unscrewed the water supply line and cut the ice maker and fresh water outlet lines from the valve. inserted the fresh water and ice maker lines into the correct valve and connected the supply line to the inlet. Connected the electrical lines and remounted the Valve. Turned the water on and checked for leaks. Remounted the Valve and installed the back cover. Plugged the fridge in and ran the front fill until water came out (1:00 minute). Cleaned up and pushed unit back into cabinet.

-unplugged the refrigerator
-replaced water filter inside refrigerator
-turned off water suppy at valve
-unscrewed tin cover on lower part of refrig
-took brace off that holds the double water valve
-disconnected water lines and caught excess water in a bucket
-pulled out both electrical plugs out of old dual pump
-blew out with air the black water line that runs diagonally from the part to the top of refrig going into ice make(to make sure not clogged)
- Installed the new part and reconnected all of the above.
plugged in the refrigerator
opened the valve to let water flow inot refrigerator.
done--but still no ice cubes? HELP!

Replacing the water valve was easy - the video was excellent. However, the problem was not solved - no water even after replacing the water valve. Anyone have any other thoughts?

Rolled the fridge away from the wall, unplugged the unit from the wall outlet, and removed the back panel by taking out the 6 1/4" nuts that held it in place. Vacuumed the dirt and dust out, and sneezed viscously for 2 minutes. Removed the 3/16th nut holding the water relay. removed the inlet water line, and quickly replaced it. dried off, then went down stairs and turned off the saddle valve. mopped up the water, then removed the water inlet valve. Removed the 2 water lines to the unit (Ice and water feeds) and removed the 2 wire connectors. reversed the process in installation, except the drying myself off part, and sneezing from the dust and dirt.

It went exactly like the repair video showed. I removed the back cover, unhooked the water lines, unplugged the electric connections, and replaced the valve. That video made it super easy and it is now working like it should.

Just turn the cartilage out and put the new one. Very simple

Changed out the double outlet valve which was pretty easy, after getting the right one, had the wrong part number for the first valve, not PartSelects fault, but still no water.Before changing valve, ice maker stopped making ice, figured the valve went bad on both points. After changing valve, got ice but still no water.Now what? Pulled the front cover off the freezer door where you get ice and water and found the bracket, } that holds the micro switch that works the water valve broken and the switch dangling. I screwed the switch back to the spacer between it and the frame and glued the spacer to the frame with plastic crazy glue.Got water!

pluged the wire harness into the new socket from the back and snaped the socket in place.

per the video - took off panel, remove the existing part, and replaced.