GTRC0HBZARWW General Electric Refrigerator - Instructions

When the condensor fan motor started making those "Dying Mouse" noises I knew it was time to replace it. So I removed the fan motor and re-oiled it's lubricating packing, reinstalled it and promptly ordered a repacement moter online from PartSelect. I've ordered parts from them in the past with great results and rapid shipping. So now the "Dying Mouse" has been evicted and my wife is happy. And everyone should know, ( If Momma ain't happy, Then nobody's happy.) Thanks again PartSelect for your fast, reliable parts source with very reasonable prices.

I replaced the thermostat, temperature sensor, and the run capacitor. . . Refrigerator still not cooling. I checked the start relay and measured the input terminals on the compressor for the correct resistance. . . Everything measured correctly. In a last ditch effort before calling for service, I pulled the main board, inspected it and saw the problem right away. One leg on the compression capacitor had desoldered itself. Got out my soldering iron and applied a good amount of solder to that point. Put everything back together and turn it on. . . Problem fixed. The compressor kicked on right away and started cooling the refrigerator.

Not knowing anything about a refrigerator it was hard to find the source of the noise. Once I could isolate it we googled the appliance repair and found the video from Parts Select and the rest was a piece of cake. Saved a service call and bloated parts prices. Thank you Parts Select!!!

Remove back panel . Removed fan shroud. Replaced fan and panel. Ops ck ok so far

Gently pry out switch in door jam with screwdriver and pull both connectors off and put connectors on new switch then push switch back into the hole. Looked it up on the internet and video showed how to and also had link to new part, ordered and less than a week later the fridge is bright again. I have an older freezer also and it seems that they all use the same switches. Very Very easy

It was simple. Unpluged fan two screws remove from fan bracket unplug old fan replace with new one put fan in place out screws back plugged in fan then plugged in fridge fixed problem. And save a repair cost call out. A.J.

I followed the instructions on your YouTube video exactly and it was a snap. By far the hardest part of the repair was to fit the back tab of the fan assembly in the tight slot on the way out. The result was immediate and like having a new refrigerator. I'm a 68-yo retired woman but thanks to you I now feel empowered -- will tackle next appliance repair with confidence. Thank you.

removed the inside fridge electrical panel and swapped switches

I removed cover above the light from the back of the freezer. I removed the fan and clipped the wire leads, after disconnecting the breaker to the fridge. I connected the wires with wire "union" from Radio Shack. Could have used wire nuts. I put the breaker on to check that it was running, then put the cover back on. However, to fix the build up of ice on the coils in the back of the freezer, I also replaced the thermisor and the heater coil after defrosting the coils with a hair dryer. Both were easy repairs and the fridge works fine.

Googled the model number of refrigerator with symptoms of "refrigerator wont run". Parts select web site appeared on my screen, opened Parts Select website, Partselect said probable cause of my frige symptom was that the run capacitor usually burns out 51% of the time. They were correct with the diagnosis 100%. I ordered the run capacitor for $23.00, installed it in 10 minutes, refrigerator runs good as new. Thank you for saving me cost of service call. I probably saved $200 or more. I will use Partselect again with my next problem. THANK YOU,

easy pry out, disconnect wiring, connect on new switch and press in switch.

Watched a youtube on capacitors- though on a motor with a pulley, the symptoms were the same, motor running and pulley not turning-bad capacitor. Took a chance for a 17+ dollar part vs a new compressor. It worked.

First I flipped breaker to off position for refigerator, Pulled down on socket and broke it free. Then took needle nose piars to pull wire and plug out from hole, so I could conect to new light socket then snaped it in place . Hardest part was getting wire and plug out of hole.

Pulled out old socket.pushed in new one.

I started removing the switch by prying on the right side with a screwdriver, when it emerged enough I used pliers to finish removing it. I then unpluged rhe wires from the bad switch and pluged them on the new switch and "poped" it into the hole.