GTRC0HBZARWW General Electric Refrigerator - Instructions

I found a replacement evaporator fan motor and 2 mounting bracket grommets at PartSelect.com at a reasonable price. I watched the installation video provided and installed the new parts as shown in the video start to finish installation time 22 minutes.i

Just as your video described, although due to the age of the fridge, it took a bit longer to remove the defective switch. Your video made this so simple, I can't imagine why we lived with a dark fridge for so long! I was ready to buy a whole new fridge, as repairmen are often nonexistent for small repairs. I am the biggest fan of your company & it's repair video. THANK YOU SO MUCH

Using plyers Pulled old switch down and out. Put new one in and pushed new switch up into position. The switch plugs into the contacts, no wiring needed. Worked like a charm. You saved me 200 dollars GE repair bill. Thanks

My compressor fan that blows over the coils was not spinning. I measured 120 VAC going to the fan so I knew it should have been spinning but wasn't. Took fan motor out and took it apart and super lubed the motor to get it spinning again temporarily until I could get the new one in. Put new one in and has been working for about 10 days now. Freezer is not below 0 deg F which is what you want. Frig is below 40 deg F also what you want.

On partselects video the gentleman removes the fan and housing in one piece. This is a great idea but does not work on this brand of ge. I removed the fan housing screw as instructed but left it in place and swiveled it enough to access the retaining screws with a socket driver. Over all swap of the fan was seamless and the video is a gem. Andy

Condenser fan motor was running slow. This was not a problem included in your list of possible problems. I thought that maybe the capacitor was bad but have no way to check it. So I ordered one. when I received it, I installed it. That was not the problem. So I ordered a fan motor and installed it. That was not the problem. So finally I ordered a control board and installed it. That solved the problem. So maybe you should put "cond.fan motor runs slow" in your list of possible faults and what causes that problem. Capacitor was easy to install, simply remove the cover plate, flip off retaining wire, unplug the capacitor and replace. Fan motor was a bit more difficult. It must be removed from mount after fan scroll is removed. Remove one screw that holds scroll, bend the top down and remove. Then pull hard on fan blade to remove it. It must be installed on new motor. Two screws in frame mount can be removed with some effort if you have a 1/4" drive ratchet with a Phillips screwdriver bit. Then pull frame open and install new motor. Push fan blade on new motor shaft hard. Replacing control board was easy. I used a pair of long nose pliers with 90 degree bend to get mounting pins closed to pull board off.

I followed the instructions in the video regarding removal, repair and reinstall. It all went as the video said, except for the reinstall. The rear tab did not snick into place like the one in the video did, and it was extremely difficult to see whether or not it was inserted properly. I ended up inserting the rear tab by feel, and then I had to hold it in place while I stretched the front part of the frame to line up the screw hole in order to reinsert the screw. I had to have my wife hold the flashlight while I did that in order to see. Other than that, the repair went well, it is working like a charm, and I know I have a quality GE part in my refrigerator again! Many thanks to Partselect for their speediness in getting the part to me and giving me the needed information in getting the repair done! I will shop here again.

condenser fan on bottom condenser not runningchanged fan and fan motor

about an hour to figure out what was causing the vibration and noise and about an hour to put it back together and 5 min. to order a new fan blade thank you.It started making noise during thanksgiving dinner so we toke it apart after dinner and I cut the other 2 blade to match the broken one so to cut down on the noise and vibration semi put it back together and 7 days later the part arrived.

Just follow the instructions from the Youtube, the link to the video is included in the sheet coming with the part. It was easy to take the entire compartment out as instructed, however, after replace the old motor with the new one, it took more than 20 min to put the entire compartment back after trying different ways. It has been working greatly since it was repaired.

took screw that holds motor frame in place out with nutdriver, rolled motor frame out after unplugging motor,took screw out of strap that held motor in frame, removed bushings from old motor and put them on the new one and re3versed the proceedure.

Follow the directions on the video, removed the back panel, unplugged the existing fan, removed the fan assembly, installed the new motor and reassembled the components.

per your instructions

Removed rer cover, unplugged starter assembly from side of compressor and replaced unit with a new one. Plugged fridge in and it works good.

Water still came out the front when pressed, but no ice. After removing the Ice container, & the top shelf I noted the icemake inlet was iced over. I turned off the icemaker, turned down the freezer temp, & allowed Ice to melt, but problem returned. I next removed the back bottom cover & cleaned the condenser coils, & drain pan; they were extremely dirty. Then I noticed the condensor fan was not on. After getting the nomenclature plate info off the condenser fan motor I left the back cover off, & put an external fan to blow on the coils as a temporaty fix until I could get the part & replace it. During that time the refrig functioned normally. 3 days later my condenser fan motor I ordered from Parts Select arrived & I installed it.