GSRS3KLXAFSV General Electric Refrigerator - Instructions

shut off water supply to unit, pull the unit out,unplug, unscrew lower back cover, locate valve relay unit (bottom left, black and clear hose coming out of it) undo the quick connect for the clear water hose on the right (black one is for ice).

front of the unit, bottom left, locate the other hose (longer one) running to the freezer door from under the unit, undo quick connect.

Inside unit, remove middle drawers, careful with the glass panels as these just lay on top and are not fixed.

undo the 3 screws for the old tank, pull it out, snake the hoses thru the grommet on the bottom, reverse process...all set!

I had Sears comre and check it out. They wanted $188. for the part and wanted $211 to put it in. They had the part in the truck. The fridg is a GE Profile and only 2 years old. Told them to forget it. Took me literally less than 10 minutes. They did a diagnostics, cost me $77. they told me the problem. I ordered the part here. It came in 3 days and the directions included were awesome. straight forward. Nice to know there is a place to go to avoid getting the shaft from appliance giants. Thank You !

The details: removed the 3 screws, took a picture of the board, didn't need it, unplugged the 6 plugs. pushed 3 clipds holding the board, unscrewed the ground, removed the board, lined up the 3 clips and snapped the new board in place, replugged the plugs and screwed in the ground. Plug the fridg in, done. Literally that easy.

Just pop the old one out, careful not to lose the wiring inside the ref wall & popped the new one in.

Removed water filter and turned off water supply. Remove the metal plate at the rear bottom of refrigerator and the metal plate at the top rear of the refrigerator that covers the exit of the filter housing from the refrigerator. Then disconnected the water supply line and water line from the filter housing mount to the valves that control water to the door and ice maker. From inside the refrigerator, removed the two bolts holding the filter housing and then removed the filter housing and tubing. Reversed the procedure to install the new top filter housing mount with tubing.

After I bought what I thought I needed for the repair. I asked a friend to come over and look at it. He changed the
the light socket and put the same light bulb in and it works great. I am returning the light switch but decided to keep the light bulb.

Getting on the internet was so easy. This was really very simple. Thank you for making what I thought would be a big ordeal into something very simple.

Paulette Johnson

The refrigerator was staying in defrost too long allowing the temperature to rise to the point that part of the ice (probably some of the food too) to melt then re-freeze. I first changed out the temp sensor and thermostat because I wanted to try the cheap stuff first but that didn't fix it, I should have gone with the mainboard first as it was the most likely cause. After putting in the new mainboard in the thing has worked perfectly since. The board was extremely easy to change, take the metal cover off with a nut driver. Carefully unplug the wires from old board and remove the board. The board is mounted on some plastic standoffs that expand after passing through the board, some of these came out while i was disconnecting the wires but some were there to stay until I figured out that I needed to squeeze the top of them to release the board. After getting the old board out just put the new one on the standoffs and connect the wires. Put the cover back on and DONE!

NOTES: The new board had some extra connectors that my old one did not, but the correct connectors were still in the old locations. The instructions that came with the board did talk about making some modifications to the refrigerator wiring on certain models, but that didn't apply to me. If I remember right the models requiring modification were all bottom freezer type. But even if you do have to do this the instrucions looked easy, just cut a couple of wires, no splicing or anything.

opened refrigerator door located water filter location in right back corner unscrewd 1/2 turn and out it comes without shutting off water it is a snap to do by anyone and shipment was really quick thanks. People do not call a service tech for something this simple even a child tall enough can do it.

remove by hand turning old and replacing new by turning by hand.Lifted out old grill and placed in new one

I ordered the part on Sunday and had it by Tuesday. It only took a few minutes to install. Basically, I unplugged the unit and removed the cover over the motherboard with a nutdriver. The wires were easy to unplug and reinstall. There was no way to incorrectly install since they could only fit in the correct position. I reinstalled the panel pluged it back in and now the fridge is working great.

Remove lower front panel, disconnect damaged union from water hose under freezer door, replace with new union, tighten and reattach front panel. No more water coming from under the unit. Ice maker and dispenser features returned to working order!

Took the three screws out of the cover, took the six plugs off of the board and removed board.

By following the instructions in the manual that went with it, I used the parts in the order that the instructions said. The illustrations were very easy and now we dont have to use ice cube trays any longer. Any person without experience that can follow directions can put in an icemaker with the simple to follow instructions that was used in the manual.

Unplugged the old ice maker. Removed the two screws that held it in. Removed the old ice maker and replaced it with the new one. Put back the two screws, plugged it back in and turned on the power switch. It started making and dropping ice in the first 1/2 hour.

My wife and I decided to tackle this job on a Saturday. The fridge was due for a good cleaning anyway. We pulled it out and shut off the water to the ice maker.
I took out the old ice maker, (two screws and the plug) Then went to the back of the fridge. removed the cardboard cover at the bottom of the frigdge and took the mounting screw out of the water valve. I had a double valve for the no longer working in-door water so I made sure to identify Then installed the new water valve. Note: be sure to check your connections for leaks before mounting the water valve - it is easier to see and fix them !!!! You can leave the water on at this point because the icemaker and water valve will not operate until the icemaker is plugged in. Next choose the right water fill cup, and install the ice maker to the existing screw mounts and plug in the connector. Note: be sure the ice maker is turned off. Start the fridge, let it get cold, then turn on the icemaker.
Overall this is a great multi install package - Don't worry about extra parts because you will have some. If we would have just needed to do the icemaker and not clean the fridge, I could have done it in about an hour.
Overall I would highly recommend this package vs what is available at other retailers for more money. Best Buy has a bargain replacement icemaker but does not have the versatility and completeness of this product. I give this product 5 stars.... dm

Watched video, however could not get outer casing off. Under the panel are three small holes, pushed up with an Allen key, used a small screwdriver to wedge out, came out easily, followed instructions from video on removing and replacing solenoid