GFRF2KBYHWW General Electric Refrigerator - Instructions

I followed the step by step instructions on provided by Part Select. I replaced the coil heater and temperature switch.

Condenser fan motor was running slow. This was not a problem included in your list of possible problems. I thought that maybe the capacitor was bad but have no way to check it. So I ordered one. when I received it, I installed it. That was not the problem. So I ordered a fan motor and installed it. That was not the problem. So finally I ordered a control board and installed it. That solved the problem. So maybe you should put "cond.fan motor runs slow" in your list of possible faults and what causes that problem. Capacitor was easy to install, simply remove the cover plate, flip off retaining wire, unplug the capacitor and replace. Fan motor was a bit more difficult. It must be removed from mount after fan scroll is removed. Remove one screw that holds scroll, bend the top down and remove. Then pull hard on fan blade to remove it. It must be installed on new motor. Two screws in frame mount can be removed with some effort if you have a 1/4" drive ratchet with a Phillips screwdriver bit. Then pull frame open and install new motor. Push fan blade on new motor shaft hard. Replacing control board was easy. I used a pair of long nose pliers with 90 degree bend to get mounting pins closed to pull board off.

Open up the freezer make shore the fan is running/unplug the unit take out the Shelf,s take a 1/4 inch nut driver and take the back panel out pull out the ice box pull up on the back panel and pull it out to expose the coil it should be blocked with ice if it is take a blow dryer and defrost it unplug the fan and push it up. On top of the coil you will fiend the defrost timer take your hand and unstrap it and pull it out. Cut the wires and strip the wires back enough take the new part and wire nut the wires together and tape with electrical tape and put back on the coil. Put every thing back together your dun plug the unit in and wait over night if you can to let every thing cool.

I watched the video then ordered the defrost timer it was here in two days (ordered late saturday arrived tuesday). Spent $. 16 On two wire nuts and went to work . The repair took one hour including defrosting the coils with a hair dryer . Your website is my " go too " for parts and repair. I spent less than $20 including shipping !

Replaced the Defrost Thermostat and the Defrost Heater.

1.- ordered the thermostat replacement.2.- unplugged unit 3.- empty unit, removed racks too(freezer only) 4.- used a hot hair dryer to melt the ice,kept drying water inside the unit. 5.-used electrical pliers carefully removed damage thermostat.6.- putted on new thermostat, used standard wire connectors to keep wires together and wrapped them with black electrical tape. 7.-gentle replaced thermostat back in contact with the other pieces.8.- returned back racks and all removed pieces,drying all water from melted ice.9.- plugged it,...done

I looked at the video that came with the part and followed what i saw. My wife and i was about to go out and spend between $1500 and $2500 on a new refrigerator due to continuous defrosting. It had been happening for about a year. I followed the instructions from the video and the defrosting has stopped. Thanks so much for the video and the part! We do not need a new refrigerator after all.

I called a repair shop and they said the control bd. was bad. They replaced it and about 2 weeks later it happened again. They came out again and replaced the bd. under warranty. About a week later it happened again. This seemed like too much of a coincidence, so I looked around on the internet and found your site. The video showed how to replace the freezer safety thermostat which I ordered on Sunday and received on Tuesday. By then the coils were iced up again. I completed the repair in about half an hour. So far the old GE is working like new. Thanks for the help. I just wish I hadn't spent over $400 for incompetent repair people in the first place. Thanks again, you guys are great! By the way the part only cost about $17 including shipping.

The mother board was bad....solder the board and it works like a charm.

Really easy unplugged unit took off back panel in the freezer thawed out coils remover sensor replaced with the new one put the unit back together works fine took about 35 min.

Removed back panel,removed ice maker.And you can see the two wires colors are a snap to identify cut the two wires spliced the new one in done deal!

Emptied Freezer (to get access to panel covering condensor coils and Defrost Thermostat). Pulled off cover panesl. Had to wait for ice to clear from condensor. Replaced Defrost Thermostat (5 min job), replaced panels and was back in business.

Very limited working space in this model. Must remove grill and disconnect elect connector on motor. One additiional tool suggested: Extendable rod with magnet on end because you will most likely drop something. First, remove two screws holding motor to metal strap. Tool must be inserted between blades of fan in order to get to the screws and this is the hard part. Fan and motor are removed as one assy and this takes some manuvering. Might have to remove front screw on metal strap to gain more room. I did not attempt to remove fan shroud. My fan was attached to the motor shaft with a metal clip. Spray a good lubricant such as PB Blaster on the shaft, wait a few minutes and press it or tap it out gently. Save misc parts on old motor for reassembly. Your set up may be different so check out everything before starting.

pull out the slide pan lh and replace for the part

the parts I ordered did not fix the problem the problem was with repairman did not follow the instruction and cut jumper wire on main control board