GTL22JBPARBS General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- JULIA from WARWICK, NY
- Parts Used:
- WR72X10073, WR72X10072
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Socket set
Left Slide Pan Broke Off, Needed To Replace It
Remove entire shelf from refrigerator and removed broke, set the replacement part in place, screwed it in and it worked perfectly, done infive minutes. Took me longer to take out the self that to do the replacement.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wayne from Rancho Cordova, CA
- Parts Used:
- WR55X10025
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Refrigerator freezing.
Temp. Sensor was under an egg shaped cover on the left side wall in the refrigerator. Remove the cover, cut the two wires to the old sensor and remove it. Connect the new sensor to the two wires using butt connectors. Replace cover and done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- larry from lisbon, ME
- Parts Used:
- WR55X10025
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
extreme frost build up inside in back of freezer,also veggies were freezing in the fridge draw
no brainer,watched the video,worst thing was to thaw the freezer,it was realy frosted,works like new,very happy thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vernon from Harmony, NC
- Parts Used:
- WR55X10025
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
coil frosting up and refridgerator section was not cooling
took out shelves and removed the back plate my removing 2 screws with a nutdriver.removed the old defrost timer and defrost heater which was really easy.then installed the new ones.the video i watched on the website was really helpfull.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from Golden, CO
- Parts Used:
- WR60X10220, WR02X10098
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Refrigerator over cooled, discovered condenser fan had failed.
Follow the directions on the video, removed the back panel, unplugged the existing fan, removed the fan assembly, installed the new motor and reassembled the components.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John J. from Deland, FL
- Parts Used:
- WR55X10025
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
freezer no cold enought
as per video- follow all of the videos and u r going to save a lot of money tx partselect im glad I found u guys ps only order from partselect.com they only ship the correct parts remember look at the video select the symptom and buy as per video tx again problemsolved
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john from Marquette, MI
- Parts Used:
- WR60X10257
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
fan did not work
Removed plastic housing and metal back panel,then removed fan motor and reinstalled everything. In all it took about 20 minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Raton, NM
- Parts Used:
- WR60X10220
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Condensor Fam Motor Noise
When the condensor fan motor started making those "Dying Mouse" noises I knew it was time to replace it. So I removed the fan motor and re-oiled it's lubricating packing, reinstalled it and promptly ordered a repacement moter online from PartSelect. I've ordered parts from them in the past with great results and rapid shipping. So now the "Dying Mouse" has been evicted and my wife is happy. And everyone should know, ( If Momma ain't happy, Then nobody's happy.) Thanks again PartSelect for your fast, reliable parts source with very reasonable prices.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- richard from castle rock, CO
- Parts Used:
- WR60X10220
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Fan Sqeels
Remove back panel . Removed fan shroud. Replaced fan and panel. Ops ck ok so far
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Dayton, NV
- Parts Used:
- WR60X10257
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Made a lot of noise
Remove plastic parts then remove back panel, remove plastic seround holding motor, romove 2 screws holding motor bracket, unplug motor, reinstall motor, bracket, seround, back panel DONE
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MICHAEL from Lubbock, TX
- Parts Used:
- WR60X10220
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Fan wasn't running and walls of freezer and ref. were hot
took screw that holds motor frame in place out with nutdriver, rolled motor frame out after unplugging motor,took screw out of strap that held motor in frame, removed bushings from old motor and put them on the new one and re3versed the proceedure.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- chol from Glenview, IL
- Parts Used:
- WR55X10025
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
refriger warm
replace sensor in refriger.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Glenroy from Martinsburg, WV
- Parts Used:
- WR60X10205, WR02X10098
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
The refrigerator made a humming/grinding sound
I used the socket set to remove pannel that allowed me to have access to the evaporator fan. Once the fan and it's container was visible, I removed the entire fan container using the socket set. I took the fan out of the container, removed the damage blade and the damaged fan grommets. I then replace the old blade with the new blade and put the fan and the compartment back together. I am not very handy so if I am able to do this, anybody can. Ps. I was very very pleased with the services I received from PartSelect and would encourage others to use them - must admit I was very suspicious at first.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Greg from Rockwood, TN
- Parts Used:
- WR55X10025
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Would not self defrost.
Remove the shelves then remove the back by removing the two screws at the top of the panel. Locate the temperature sensor on top of the coil. Cut the wires and replace with the new one. Use wire nuts and electrical tape to reconnect the wires.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marco from Fallbrook, CA
- Parts Used:
- WR55X10025
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
My fridge was colder than my freezer
I can't tell you how luck I feel after finding your website I ordered the temperature sensor after watching one of your videos on-line and the repair went just as on the video. I pulled the "bad" sensor out, and replaced it with the new one. Keep in mind that this is the first time I ever touch an appliance, needless to say I'm feeling pretty good about that! All in all it took me about 20 minutes to complete my repair and it now has been about 4 days and the refrigerator is working like new again!
Was this instruction helpful to you?
Thank you for voting!