34221-3 General Electric Refrigerator - Instructions

I found that the fill solenoid for the ice maker was down to a drip when energized. I ordered from this site and replaced. now plenty of water, but the ice maker would just stall and jump teeth. The heater which heats the ice up to free it from the mold was defective. Ordered from this site, and now working great.this sitet has good pricing, and the help illustration is great, and explains the sequence of events. This made it easy to troubleshoot. This refrigerator has not give a problem in over 11 years. The problem is "the ice maker". I have replaced it 6 times.

The instructions that came with the replacement icemaker were very complete, in particular concerning the small levelling bracket on the bottom of the icemaker, because the old bracket needed to be removed from the old icemaker and transferred to the new one. This part of the installation might not have been obvious, so I was glad to see it clearly outlined in the instructions. The old icemaker was removed by loosening two nuts and detaching the electrical connector, and the new one was installed in its place. Fairly simple, the whole job took about 45 minutes because I work slowly and carefully. A more confident person could probably have the new one installed in 15 minutes. Only drawback: about three to four weeks after installing the new icemaker it has begun making a loud clicking noise on occasions. It is a repetitive (5 second interval) clicking, and only happens for about a minute every few hours and then stops. I am concerned that it might be gears prematurely wearing out and slipping. I guess I'll know in a few weeks if this one stops making ice.********************************************* Update: after about 9 months the new icemaker quit working and will need to be replaced. I removed the front cover from the icemaker and could clearly see that the teeth of one of the plastic gears were worn out and no longer meshing with the opposite gear. The drive gear was just spinning in place and making no contact with the larger gear.

Removed from freezer and dumped ice into pan. Removed 5 screws and pull old bin out. Inserted new bin in place and reinstalled 5 screws. Put back in freezer and dumped ice into bin . Job done

i watched the video very simple repair

Followed instructions in video that was suggested when I placed the order.

Put a new door bearing and problem solved

Removed 2 screws that hold ice maker in place. Unplugged and took out of freezer. Used the screws I took out to put new ice maker in. Plugged in the power and in 2 days I had a full ice bin and haven't had any worries since. Should have replaced the broken one along time ago but thought that the process was harder than this. Very easy and suggest this to anyone having ice maker issues. Less than $100 and never have to buy ice for the house again.

Removed ice maker bin...removed screws and housing and reinstalled all...very easily completed.

Ordered ice maker, watch video of how to. It takes less than 5 min. Installes just like the video. Loosen 2 1/4" Screws, lift ice maker up, unplug old unit, Reverse. Just make sure water tube is lined up when you install new unit and wire is tucked up out of the way. Mine did not really start making ice till the next day.

We love our ice here. I seem to replace the ice makers one to two times a year. Generally the ice cycle gets off for some reason and it starts making loud popping/clicking noises (gear grinding). Its easy to replace. Simply loosen two screws holding the unit to inside of freezer and disconnecting the wiring harness. Unit slide up and out. Replacement is super easy (5 mins or less). Bam! Ice!

0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.

No tools needed, the cap is just held in place with pressure from the wire.

I loosened the 2 1/4 inch nuts with a nut driver, disconnected the wire harness, and removed the old unit. to replace, I simply connected the harness and bolted the unit back in. The job took about 10 to 15 minutes and the new unit works better than the old one ever did.

Slid out old ice tray, inserted new one. Worked perfectly.

It was very simple, used a nut driver to loosen the attachment nuts that held the ice maker in place. Disconnected the wiring harness. Removed the leveling tab from old ice maker and attached it to the new one. Then reassembled in the reverse order. As they say it was no brainer! The best part of the repair, was hearing the ice dump.

Emptied everthing on the RT.Remove upper guard and hinge,lift door off of lower hinge.Set it down somewhere safe.Remove lower hinge,replace with New Hinge,Door part # 5303918455, Closer Bushing part #240457702. Put the back on the frige,Boom done.."Miller Time" [or whatever You prefer} I had this problem before,and I see Frigidaire upgraded the hinge and the Plastic Bushing..Thank You