Models > GSR23YBWKSS > Instructions

GSR23YBWKSS General Electric Refrigerator - Instructions

Jump to:

All Instructions for the GSR23YBWKSS
121 - 135 of 217
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
aaron from reynoldsburg, OH
Parts Used:
WR23X31507
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers
Hing door brine off
Poped whole switch out with flat head screw driver. Removed wires with needle nose players and held the wires so they wouldn't get pulled back inside fridge shell. Attached wires to new part like a plug. Lights ccame back put new switch back inside wall. Shut door
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Roscoe G from ROCHESTER, NY
Parts Used:
40A15
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Light burnt out.
Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.
2 of 8 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Guntis from Sugar Grove, IL
Parts Used:
WR23X31507
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Refrigerator light switch in door did not work
Pried out the old light switch, disconnected electrical, reconnected electrical in new switch, pushed new switch back into door.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Donald from Roseville, CA
Parts Used:
WR49X10091
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Refrigerator was running so cold the vegetables froze
Following the lead of other posted on this site, I removed the old air inlet cover after emptying the refrigerator. (That took the most time) 1. It's easiest if you remove all the shelves. 2. To access the upper two screws remove the top light cover - it has press in holders on each side. 3. As mentioned in other posts, there are four screws holding the Inlet Cover in place, 2 lower and 2 upper. 4. To get access to the lower two screws,you simply pop off the lower duct assembly. Take out the screws and remove the air duct. Unplug the electrical connector. 5. I had to use the added insulation spacer to seal the unit into the cold air opening. 6. Plug the new air inlet cover unit in and put back in place. 7. Install screws, put lower duct back in, and put light cover back in place. 8. Since shelves were all out, it was easy to give them a good cleaning and put they whole thing back together. 9. Relax and have a cold beverage of your choice. (I took old air inlet apart and lo and behold, the damper door was broken off. Problem solved.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Dan from Bethel Park, PA
Parts Used:
WR51X10055
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Refrigerator not getting cold. Frost in freezer
First replaced the defrost sensor. Same issue. Tested ohms on heat element basically open. Very high resistance Mega Ohms. Ordered new element 21 ohms. Installed 30 minutes. Only needed a Phillips. Set Frig on 5 setting and working well.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Ajaykumar from Plainsboro, NJ
Parts Used:
WR60X10209
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
The refrigerator was making load and unusual noises.
I identified the noise was coming from the coils / and the fan. Cleaning the fan helped reduce the noise a bit but it still kept recurring. I ordered the part, which was really easy using the diagram on the website. The instructions and the video were really helpful and was able to remove the old motor and replace it with the new one with relative ease. While there I cleaned the fan blade and vacuumed the surrounding area. This whole repair went quite smoothly and has given me the confidence to take on other repairs before calling out the repairman.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Kenneth from Charlotte, NC
Parts Used:
WR23X31507
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
broken light switch
Used a small screw driver to remove the damaged switch. Carefully unhooked the two wires and hooked the wires to the new switch. Pushed the new switch into place. Be careful that the wires do not pull back into the refrigerator wall. Took about 15 minutes. Works like New. Easy fix.
Was this instruction helpful to you?
Thank you for voting!
Customer:
guy from bandera, TX
Parts Used:
WR51X10055
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers, Screw drivers
frezzing up in the coil not defrosting
unpluged the fridg. let defrost.removed shelfs/removed screws on side rails that hold shelves /re moved back plate / unconected red and blue wires/two screws discnneted the unit. reverse steps 1 to 9. fride works perfect now
Was this instruction helpful to you?
Thank you for voting!
Customer:
Paul from Hampton, AL
Parts Used:
WR51X10055
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Freezer frosting up so bad it would no longer cool my fresh food
I had replaced the thermastst first because 40-50% of people this solved the same problem that I was having. Not only that it was only $10.00, my multi meter was broken so a $10.00 part was less expensive than a $40.00(+-) meter to test what was broken for sure. Well that did not fix the problem. I read all the "repair reviews" on here and found that more than likely it was my heater that was bad. So next time I defrosted the freezer I was able to get a peak at the "bulb" on the heater, it was BLACK! I ordered the part ($50.00) and was totally surprised how EASY that was to put in!! It took way longer to defrost than install this part! My wife came to see, saw what I had to replace, and said sarcasticly "have fun figureing out how to get that off!" She came back in 10 min and I was putting the back panel on the freezer, she said "where you not able to get it off!?" I did not say a word just handed her the burnt out one with a grin! That was about 2 weeks ago everything is working fine... Of course I replaced my muli-meter already, but never even used it on the fridge! Oh well I got my fridge repaired and a real nice multi-meter for way less than a repairman would have charged!
Was this instruction helpful to you?
Thank you for voting!
Customer:
Kenneth from Brentwood, CA
Parts Used:
WR23X31507
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Coke can exploded when dropped and some got on the switch making it stick in off positionmaking thehe switch stik
Pried the switch on the bottom with a flathead screwdriver, twisted it and the switch came out far enough to take it out by hand. The bottom of the switch has to be raised upward a little because the connectors are on top of the switch. Changed the wires from the old switch to the new one, one at a time. Insert the new switch. Saved a repair call, and probably a more expensive switch. Less then 15 minutes.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Carol from Petaluma, CA
Parts Used:
WR49X10091
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
The refrigerator side was too cold freezing items
The thermostat was set at 0 for the freezer, but at 37 for the refrigerator. The refrigerator was showing a temperature of 20 degrees and would not stay at 37. After learning the 3 choices it could be (air inlet cover, thermostat, and computer), I went for the air inlet on the basis of percentage of repair. With this particular refrigerator with this problem; this is repair has the highest chance of success. Nice on-line decision making tool! I went with choices of previous buyers and followed previous buyers instructions. All I needed was a couple of Phillips head screw drivers, and cleaning the dirt I was finding in the refrigerator was the biggest job.
Was this instruction helpful to you?
Thank you for voting!
Customer:
James from Taylorville, IL
Parts Used:
WR51X10055
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
Refrig would not defrost
Replaced the Defrost Heater and Bracket Assembly
Was this instruction helpful to you?
Thank you for voting!
Customer:
Clarence from Mesa, AZ
Parts Used:
WR49X10091
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Vegetables were freezing in the drawers
Followed directions and it was quite easy.
Was this instruction helpful to you?
Thank you for voting!
Customer:
erik from erie, CO
Parts Used:
WR49X10091
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Our GE Monogram's freezer and flood locker compartments were too cold
This website is awesome! It basically tells you exactly what is wrong with your fridge. Our food side of the refrigerator was getting way too cold. Some items actually froze. I looked here and it said the fan/ damper assembly was broken. All I did was remove the part they said was broken and sure enough the little damper door that lets freezer air into the fridge side was broken. I ordered the part, replaced it and presto the refrigerator holds perfect temperature again! The replacement was super easy...only tool needed was a screwdriver and 15minutes! Thanks
Was this instruction helpful to you?
Thank you for voting!
Customer:
juris from gainesville, FL
Parts Used:
WR51X10055
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Freezer Not Defrosting
A very simple install. Requires the removal of 4 screws and plugging in new heating element refer to the excellent diagrams provided on line
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the GSR23YBWKSS
121 - 135 of 217